UCC2897A Peak Current Mode Active Clamp Forward Converter Small Signal Modeling Design Consideration written by Chinese engineer

One of the most predictable non-linear elements commonly available is the bipolar transistor. Therelationship between collector current and emitter base voltage is precisely logarithmic from currentsbelow one picoamp to currents above one milliamp. Using a matched pair of transistors and integratedcircuit operational amplifiers it is relatively easy to construct a linear to logarithmic conv

This document introduces a general formula to translate the phase noise of a clock source rated via the Single Sideband to Carrier Ratio to the cycle-to-cycle jitter of the oscillation period. The link allows to seamlessly aggregate the external clock source phase noise usually given in dBc/Hz to the phase stability figure of the on-chip clock synchronization circuitry usually rated in ps-RMS

This application report provides a reference design for Power over Ethernet (PoE) on the Power Device (PD) side using Texas Instruments LM5070 and the physical layer device DP83865 Gig PHYTER™

In telecommunications and signal processing, frequency modulation (FM) is encoding of information on a carrier wave by varying the instantaneous frequency of the wave. Digital data can be encoded and transmitted via carrier wave by shifting the carrier's frequency among a predefined set of frequencies—a technique known as frequency-shift keying (FSK). FSK is widely used in modems, radio-teletype and fax modems, and can also be used to send Morse code.

Frequency-shift keying (FSK) is a frequency modulation scheme in which digital information is transmitted through discrete frequency changes of a carrier wave. This application report discusses logiclevel implementation of binary FSK (BFSK) modulator and demodulator using a phase-locked loop PLL device – CD54HC4046A, CD54HCT4046A, CD74HC4046A, and CD74HCT4046A (hereafter in this document referred to as HC/HCT4046A). BFSK is the simplest FSK, using a pair of discrete frequencies to transmit binary information.

LB-25 True rms Detector

AN-258 Data Acquisition Using the ADC0816 and ADC0817 8-Bit A/D Convert er with On-Chip 16 Channel Multiplexer

Customers have evaluated several TI power-management (PMU) devices and have found that somedesigns can make the PMUs operate beyond typical data-sheet application specifications. This reportreviews the backgrounds of various relevant design features of a family of 5-V CMOS sub-PMUssuggests solutions to accommodate system requirements mitigates radiation concerns and proposesbest practic

The TPS61140/1 is a dual output boost converter providing regulated voltage and current output with one boost converter. The reference design and application example shown in this document can be used

This document describes the design considerations required to change a bq2084 design to a bq2084-V133 solution. Find the latest ordering information and data sheet on the World Wide Web at http://powe

This document describes issues of interest related to migration from the TMS320VC5410 to the TMS320VC5410A. The objective of this document is to indicate differences between the two devices. Functions that are identical between the two devices are not included. For detailed information on the specific functions of either device refer to the device data sheets 5410 (SPRS075) 5410A (SPRS139) the

CC1120 CC1121 CC1125 CC1175 CC1200 CC1201 CC1111 CC1101 CC1110 CC110L Miniature Helical PCB Antenna for 868 MHz or 915/920 MHz CC113L CC115L

This gold(Au) embrittlement study evaluates TI?s original four-layer nickel-palladium(NiPd) lead finish that was introduced in 1989 and TI?s nickel-palladium-gold(NiPdAu) lead finish that replaced four-layer NiPd in 2001. Samples were prepared with three different Au thicknesses for the NiPdAu components. The printed wiring board(PWB) finishes used were organic solderability preservative(OSP) and

6A Termination Supply Tracks 1/2 Core Voltage

Power consumption on an Ethernet PHY is affected by different operating conditions. System design around Ethernet products requires accurate power consumption numbers for component selection thermal management and power distribution planning. This application report details power consumption of DP83867 in different conditions.

This application report describes how to interface an MSP430 mixed-signal microcontroller with the TLC549 and TLV1549 3-volt A/D converters. This report is written for the MSP430x11x(1) family, but ca

This application report contains complete code examples for routines that have been developed using a TMS320C54x? EVM platform. These programs demonstrate applications that use a host interface and run in real time.

GTLP in BTL Applications