Manufacturer
MORE

Displaying 4001 - 4020 of 6622

Application Notes

Using UBL to Boot Custom Application

Texas Instruments
This application report discusses how to use the UBL to load a custom application developed on Code Composer Studio™ to DDR and then to execute the application from DDR. The UBL, sfh tool, and c

Programming Audio Power Up/Down on TSC210x & TLV320AIC26/28 (Rev. A)

Texas Instruments
Programming Audio Power Up/Down on TSC210x and TLV320AIC26/28

AN054 -- Anaren balun optimized for CC2420

Texas Instruments
AN054 -- Anaren balun optimized for CC2420

High-Resolution Microstepping Driver with the DRV8828/29/40

Texas Instruments
This application report is provided as a supplement to the DRV8828, DRV8829, and DRV8840 product data sheets. It details the hardware implementation of the DRV8828/29 and an MSP430F2112 microcontrolle

Highly Integrated PMIC for Powering the Marvell PXA270

Texas Instruments
This reference design was created to help those needing to power the Marvell PXA270 and doing so by implementing a highly simplistic and efficient design that uses the TPS65021 power management unit.

TMS320C30 Addressing up to 68 Gigawords

Texas Instruments
The primary bus of the TMS320C30 has 24 address lines, which allows addressing of up to 16 megawords of memory. The expansion bus has 13 address lines, which allows addressing 8 Kwords. Using the tech

Dynamic Power Path Management Simplifies Battery Charging from Solar Panels

Texas Instruments
The Texas Instruments bq2403x family of linear charge regulators were originally designed to charge single-cell Li-ion batteries from an AC adapter or USB port. However, these ICs also lend themselves

Setting Up TMS320 DSP Interrupts in 'C'

Texas Instruments
Four steps are required to set the TMS320 DSP interrupts: create a interrupt service routine, initialize the vector table and set the memory map, enable the interrupts in the CPU, and enable the inter

Powering & Dimming High-Brightness LEDs w/ LM3405 Constant-Current Buck Reg (Rev. A)

Texas Instruments
AN-1644 Powering and Dimming High-Brightness LEDs with the LM3405 Const ant-Current Buck Regulator

MSP430 Based Lithium-Ion Polymer Battery Charging and Gauging Solution Using USB (Rev. A)

Texas Instruments

The use of USB power to charge Lithium-Ion Polymer (LiPo) batteries in electronic systems and devices has become quite popular. To assist in the development of such circuitry in embedded system applications this application report provides the details on the hardware and software requirements needed to not only implement a battery charging solution using the bq24230 battery charger and the MSP

How to Select Little Logic

Texas Instruments
How to Select Little Logic

LM3553 1.2A Dual Flash LED Driver System with I2C Compatible Interface (Rev. B)

Texas Instruments
This application note describes how to operate the LM3553 Evaluation Module.

AN-1507 DP83848 and DP83849 100Mb Data Latency (Rev. B)

Texas Instruments
The purpose of this document is to define the 100Mb Transmit and Receive latencies of the TexasInstruments Semiconductor DP83848 and DP83849 Ethernet Transceiver family and to document theircontributions for end-to-end packet transfer in both MII and RMII modes of operation.

Software I2C Slave Using the MSP430

Texas Instruments
This application report describes the design of a software I2C slave that can run up to 100-kbps using an MSP430 MCU. This software I2C uses a small amount of MCU resources so that it can be implement

DRV10983EVM-TB Target Board Programming Guide

Texas Instruments
This guide assists the user in programming the DRV10983 whether through the TI programming socket or a custom solution. The following procedures aid in creating a system for programming prototype or production devices. Standard I2C is used to communicate with the device to read and write values to the registers.

Using xdsprobe with the XDS560 and XDS510 (Rev. A)

Texas Instruments
This application report familiarizes the reader with the xdsprobe utility. This utility may be used to troubleshoot Code Composer Studio™ 2.00 and 2.10 initialization problems that normally manifest themselves as an error message that indicates that the target DSP cannot be initialized. This problem may be caused by incorrect configuration or hardware problems in the JTAG scan path. The

Interfacing the DAC8871 to the MSP430F449

Texas Instruments
Interfacing the DAC8871 to the MSP430F449

H.263 Loop Back on the DM642 EVM

Texas Instruments
The software demonstrates the D1 H263 encoder and decoder on the DM642 Evaluation Module (EVM). The demonstration encodes the captured frames and then decodes the generated H263 bit-steam to display the decoded frames.

The demonstration uses:

  • H263 encoder library optimized for a DM642 EVM
  • H263 decoder library optimized for a DM642 EVM
  • H263 encoder and decoder library implemented

Using Advanced Event Triggering to Find and Fix Intermittent Real-Time Bugs

Texas Instruments
Finding intermittent bugs in an embedded system can be a challenge. In a real-time embedded system the challenge increases. In addition to setting breakpoints at the precise occurrence of the problem the user must be careful to not interfere with the timing characteristics of the system. By changing the timing of the system the problem may either go away only to surface later or new probl

Displaying 4001 - 4020 of 6622

Latest Parts

SC1112

Raspberry Pi

$79.61 - $80.00

IN STOCK 10122
Buy

ASX00049

Arduino

* $39.26 - * $44.92

IN STOCK 3125
Buy

AD96685BRZ

Analog Devices Inc.

$1.72 - * $11.93

IN STOCK 4921
Buy

Reference Designs

RD006

Wurth Elektronik

RD006 - 3 W Dual-output isolated auxiliary supply for communication interfaces and measurement systems

CN0583

Analog Devices Inc.

Multistandard Micropower Verified Smoke Detection System-on-Module

Technical Resources

EVALUATION KITS

EVAL-AD7124-8SDZ

Analog Devices Inc.

$71.02 - * $76.87

IN STOCK 807
Buy
View All