An Implementation of a Software UART Using the TMS320C25 (Contains Scanned Text)
Texas InstrumentsWhen transmitting to and receiving data from a processing engine such as the TMS320C25 digital signal processor, it is common to encounter problems when interfacing to asynchronous devices. This chapt
3.3V Cable Driver And Equalizer Drive Mega-Bits @ Many Meters
Texas Instruments3.3V Cable Driver And Equalizer Drive Mega-Bits @ Many Meters
Transceivers and Repeaters Meeting the EIA RS-485 Interface Standard
Texas InstrumentsApplication Note 409 Transceivers and Repeaters Meeting the EIA RS-485 Interface Stan dard
Efficiency Evaluation TPS65381-Q1
Texas InstrumentsThe TPS65381 is a multi-rail power supply designed to supply microcontrollers in safety critical applications such as those found in automotive functions. The device supports Texas Instruments’ TMS570LS series 16/32-Bit RISC Flash MCU and other microcontrollers with dual-core lockstep (LS) or loosely coupled (LC) architectures.The TPS65381 integrates multiple supply rails to power the MCU CA
TAS57xx Dynamic Range Control
Texas InstrumentsThis application report provides background information, general equations, and instructions for proper use of the Texas Instruments TAS57xx series Dynamic Range Control (DRC). Topics include I2C con
Understanding the CAN Controller on the TMS320C24x DSP Controller
Texas InstrumentsThe Texas Instruments (TI)(tm) TMS320F241 TMS320C241 and TMS320F243 digital signal processor (DSP) controllers contain an on-chip Control Area Network (CAN) module. This module is a FullCAN controller (Specification 2.0B). This application report describes the TMS320X241/3 CAN module. Software examples are included for different modes of operation of the on-chip CAN module along with an applicati
Using TI Technology to Simplify Bluetooth Pairing Via NFC
Texas InstrumentsBluetooth pairing usually involves some level of user interaction to confirm the identity of the user and/or the devices themselves. There are many pairing mechanisms available across the versions of
Transimpedance Considerations for High-Speed Operational Amplifiers
Texas InstrumentsDesigning high-resolution detection circuits using photodiodes presents considerable challenges because bandwidth gain and input-referred noise are coupled together. This application note reviews the basic issues of transimpedance design provides a set of detailed design equations explains those equations and develops an approach to easily compare potential solutions.
Solenoid Driving with DRV8841/DRV8842
Texas InstrumentsDRV8841/DRV8842 Solenoid Driving with DRV8841/DRV8842
Using GCC/GDB With CC2538 (Rev. A)
Texas InstrumentsThis document describes how to set up an open source software-based development environment for the Texas Instruments CC2538 using Eclipse as IDE.
UART Bootloader for Hercules RM42 MCU
Texas InstrumentsThis application report describes how to communicate with the Hercules™ UART bootloader. The UART bootloader is a small piece of code that can be programmed at the beginning of Flash to act as an application loader as well as an update mechanism for applications running on a Hercules Cortex™-R4 based RM42 microcontroller.
Single Cell Impedance Track Printed-Circuit Board Layout
Texas Instrumentsbq20z70/90 Printed-Circuit Board Layout Guide
OA-13 Current Feedback Loop Gain Analysis and Performance Enhancement (Rev. B)
Texas InstrumentsWith the introduction of commercially available amplifiers using the current feedback topology byComlinear Corporation in the early 1980’s previously unattainable gain and bandwidths in a DC coupledamplifier became easily available to any design engineer. The basic achievement realized by the currentfeedback topology is to de-couple the signal gain from the loop gain part of the overall tra
U-110 1.5 Mhz Current Mode IC Controlled 50-Watt Power Supply
Texas InstrumentsThe UC3825 family of PWM control ICs is optimized for high-frequency switched-mode power-supply applications. This application note describes the development of a 1.5 MHz current-mode IC-controlled 50W power supply. Push-pull topology is used for this DC-to-DC converter application of +48V input to +5V at 10A output. Increases in switching speed and dynamic performance are made possible by the U
bq2084-V133 to bq2084-V140 Change List
Texas InstrumentsThis document describes the design considerations required to change a bq2084-V133 design to a bq2084-V140 solution. Find the latest ordering information and data sheet on the World Wide Web at http:/
Interfacing the DAC8806 and DAC8820 to MSP430 Microcontrollers
Texas InstrumentsThis application report presents a method for interfacing the DAC8806 and DAC8820 single-channel, current-output, 14-/16-bit multiplying digital-to-analog converters ? to the MSP430F449 processor usin
Production 2: Data Flash Programming/Calibrating the bq20z80 Gas Gauges (Rev. B) (Rev. B)
Texas InstrumentsThis application report presents a strategy for high-speed economical calibration and data flash programming of the bq20z80 advanced gas gauge chipset family. VB6 code examples are provided along with step-by-step instructions for preparing a golden battery pack.
Using the MSP430 Launchpad as a Standalone I2C Host for Audio Products (Rev. A)
Texas InstrumentsTLV320AIC3254, TAS5717, MSP430 Launchpad Using the MSP430 Launchpad as a Standalone I2C Host for Audio Products
Transition Guide for Migrating from the bq2091 to the bq2092
Texas InstrumentsTransition Guide for Migrating from the bq2091 to the bq2092
