The TMS320C/F240 Evaluation Module provides a tool that makes it easier to design the software elements of a system when taking the initial steps in the development of a new application. This note

This application report describes the implementation of the Joint Photographic Experts Group (JPEG) Encoder and Decoder on TMS320C6000? digital signal processors (DSPs). The JPEG Encoder and Decoder are eXpressDSP? Algorithm Standard compliant. This document describes the details of JPEG Encoder and Decoder implementation APIs and measured performance.Source Code examples discussed in this a

With their low-input currents, FET input op amps are universally used in monitoring photodetectors, the most common of which are photodiodes. There are a variety of amplifier connections for this purp

CDCM1802/CDCM1804

Differences Between the bq20z70/z75/z80/z90/z95 Impedance TrackTM Gas Gauges

TMS320C3x DSK Tools and Demonstrations

To conclude the review of the UCC28517 PFC supply, this article covers the design of the second 12-V, 8-W power stage to be used as an auxiliary bias supply.

This application report describes a method of implementing the digital peak current mode control of a power supply using the Texas Instruments Piccolo™ MCUs. The theory of operation and all relevant equations are given as well as a design example and complete compile ready project files. The implementation method described is similar to that taught in Digital Power Design Workshops delivere

This design note describes a programmable electronic circuit breaker that uses the UC3843A control IC to facilitate a high-speed turnoff following an overcurrent condition. This low-cost industry-standard IC contains the required protection features and drive capability in a single 8-pin device.

This application note introduces DSP/BIOS 5.x users to SYS/BIOS 6. It provides details and an example about using the legacy support. It further provides advice about migrating applications to take ad

AN-316 The Subscriber Line Card in a Distributed Control Switching System

This application note demonstrates the use of TI?s Zero Iq Reverse Polarity Protection Smart Diode Controllers- LM74610-Q1 as a highly effective solution in redundant N+1 power supply arrangement. It

This document describes two options used to supply power to the Texas Instruments (TI)(tm) TMS320C206 digital signal processor (DSP). The TMS320C206 DSP requires 3.3V for the CPU and 5.0V for the I/O. The first solution applies when a design already has a regulated 5.0V power supply and requires only a 3.3V (LDO) Low Dropout regulator. The second solution applies an unregulated voltage input t

This article has been contributed to the TI Developer Wiki. To see the most recently updated version or to contribute, visit this topic at:<p><a href=http://wiki.davincidsp.com/index.php/OMAP-L1x/C674

The analog interface circuit (AIC), also called a modem Codec, is a complete data acquisition system on a chip for general-purpose telephony/speech applications such as: modem analog interface, voice-band audio processing, noise cancellation/suppression, hands-free communication, security voice systems, tone generation, echo cancellation, voice-over-internet protocol (VoIP), and industrial process control. The AIC is normally interfaced to a digital signal processor (DSP). This approach has a number of advantages and cost-saving benefits that cannot be realized with traditional Codec analog interfacing. The benefits include:

• lower cost,
• simple interface design and fewer components,
• greater system reliability due to fewer components,
• lower power consumption,
• higher performance, and
• high programmability.

Troika and Synoris Output Selection Filter Guide TPS65250, TPS65251, TPS65252, TPS65253

Reworking LLP Chip Scale Package

When we say that an electric motor is a device that transforms electric power into mechanical power we say two things. First that the motor is ?and behaves as ?a transformer. Second that it stands at the dividing line between electrical and mechanical phenomena. In the case of permanent magnet motors this power transformation works in both directions so that the electrical impedance depends on