AD9635-125EBZ
Analog Devices Inc.The AD9635 is a dual, 12-bit, 80 MSPS/125 MSPS analog-to-digital converter (ADC) with an on-chip sample-and-hold circuit designed for low cost, low power, small size, and ease of use. The product operates at a conversion rate of up to 125 MSPS and is optimized for outstanding dynamic performance and low power in applications where a small package size is critical.The ADC requires a single 1.8 V power supply and LVPECL-/ CMOS-/LVDS-compatible sample rate clock for full performanceoperation. No external reference or driver components arerequired for many applications.The ADC automatically multiplies the sample rate clock for theappropriate LVDS serial data rate. A data clock output (DCO) for capturing data on the output and a frame clock output (FCO) forsignaling a new output byte are provided. Individual channelpower-down is supported; the AD9635 typically consumes lessthan 2 mW in the full power-down state. The ADC providesseveral features designed to maximize flexibility and minimize system cost, such as programmable output clock and data alignment and digital test pattern generation. The available digital test patterns include built-in deterministic and pseudorandom patterns, along with custom user-defined test patterns entered via the serial port interface (SPI).The AD9635 is available in a RoHS-compliant, 32-lead LFCSP. It is specified over the industrial temperature range of ?40?Cto +85?C. PRODUCT HIGHLIGHTS Small Footprint. Two ADCs are contained in a small, spacesaving package. Low Power. The AD9635 uses 115 mW/channel at 125 MSPS with scalable power options. Pin Compatibility with the AD9645, a 14-Bit Dual ADC. Ease of Use. A data clock output (DCO) operates at frequencies of up to 500 MHz and supports double data rate (DDR) operation. User Flexibility. The SPI control offers a wide range of flexible features to meet specific system requirements. APPLICATIONS Communications Diversity radio systems Multimode digital receivers GSM, EDGE, W-CDMA, LTE, CDMA2000, WiMAX, TD-SCDMA I/Q demodulation systems Smart antenna systems Broadband data applications Battery-powered instruments Hand held scope meters Portable medical imaging and ultrasound Radar/LIDAR
DC903A-A
Analog Devices Inc.The LTC3240-3.3/LTC3240-2.5 are step-up/step-down charge pump DC/DC converters that produce a fixed regulated output voltage of 3.3V or 2.5V over a wide input voltage range (1.8V to 5.5V).With input voltages greater than the regulated output voltage the LTC3240 operates as a low dropout regulator. Once the input voltage drops within 100mV of the regulated output voltage the part automatically switches to step-up mode. In step-up mode the LTC3240 operates as a constant frequency (1.2MHz) doubling charge pump.The LTC3240-3.3/LTC3240-2.5 feature low no load operating current (65?A typical) and ultralow operating current in shutdown (
LTC4076EDD Demo Board
Analog Devices Inc.DC904A-A: Demo Board for the LTC4076 Dual Input Standalone Battery Charger.
DC913A
Analog Devices Inc.The LTC3773 is a high performance, 3-phase, triple output synchronous step-down switching regulator controller with output voltage power up/down tracking capability. The controller allows for sequential, coincident or ratiometric tracking.This 3-phase controller drives its output stages with 120? phase separation at frequencies of up to 700kHz per phase minimizing the RMS input current. Light load efficiency can be maximized by using selectable Burst Mode operation. The 0.6V precision reference supports output voltages from 0.6V to 5V.Fault protection features include output overvoltage, input undervoltage lockout plus current foldback under short-circuit or overload conditions.Applications Servers, Telecom, Industrial Power Supplies General Purpose Multiple Rail DC/DC FPGA and DSP Requirements
LTC2205 | CMOS OUT, 65Msps, 16-Bit ADC, 70MHz < AIN < 140MHz (Requires DC718)
Analog Devices Inc.DC918C-F: Demo Board for the LTC2205 16-Bit, 65Msps ADCs.
LTC2201 | CMOS OUT, 20Msps, 16-Bit ADC, 1MHz < AIN < 70MHz (Requires DC718)
Analog Devices Inc.DC918C-M: Demo Board for the LTC2201 16-Bit, 20Msps ADC.
LTC2207 | CMOS OUT, DC INPUT, 105Msps 16-Bit ADC, DC < AIN < 70MHz (Requires DC718)
Analog Devices Inc.DC919A-A: Demo Board for the LTC2207 16-Bit, 105Msps ADC.
LTC2205 | CMOS OUT, DC INPUT, 65Msps 16-Bit ADC, DC < AIN < 70MHz (Requires DC718)
Analog Devices Inc.DC919A-C: Demo Board for the LTC2205 16-Bit, 65Msps ADCs.
LTC4089EDJC Demo Board
Analog Devices Inc.DC929A-A: Demo Board for the LTC4089 USB Power Manager with High Voltage Switching Charger.
LTC4089EDJC-5 Demo Board
Analog Devices Inc.DC929A-B: Demo Board for the LTC4089 USB Power Manager with High Voltage Switching Charger.
DC938A
Analog Devices Inc.The LTC3530 is a wide VIN range, highly efficient, fixed frequency, buck-boost DC/DC converter that operates from input voltages above, below or equal to the output voltage. The topology incorporated in the IC provides a continuous transfer function through all operating modes, making the product ideal for single lithium-ion, two-cell alkaline or NiMH applications where the output voltage is within the battery voltage range.The LTC3530 is pin compatible with the LTC3440 buckboost DC/DC converter but adds programmable automatic Burst Mode operation and extends the VIN/VOUT range to 1.8V. Switching frequencies up to 2MHz are programmed with an external resistor. Automatic Burst Mode operation allows the user to program the load current threshold for Burst Mode operation using a single resistor from the BURST pin to GND.Other features include 1?A shutdown, short circuit protection, programmable soft-start control, current limit and thermal shutdown. The LTC3530 is available in a thermally enhanced 10-lead (3mm ? 3mm) DFN or MSOP package.Applications MP3 Players Handheld Instruments Digital Cameras Smart Phones Portable GPS Units Miniature Hard Disk Drive Power
LTC2482 16-bit Delta-Sigma ADC (Requires DC590)
Analog Devices Inc.DC941A: Demo Board for the LTC2482 16-Bit Delta Sigma ADC with Easy Drive Input Current Cancellation.
LTC4067EDE Demo Board | USB Power Manager with 13V OVP and 1.25A Li-Ion Charger
Analog Devices Inc.Demonstration circuit 943 is a complete power controller for a USB power device. It features the LTC6047 and provides a full-featured 1.25A linear lithium-ion CC/CV battery charger with timer termination and 4.2V charge voltage, a USB power manager, and a PowerPath manager for the battery. The USB input voltage range is 4.35V to 5.5V and the wall adapter input is 4.35V to 6V. It also features a programmable 1.5A input current limit that can be set at 500mA or 100mA for USB applications.
The wall adapter input has overvoltage protection up to 13V. An external MOSFET disconnects the wall adapter when the voltage exceeds 6V.
DC949A-A
Analog Devices Inc.The LT3478/LT3478-1 are 4.5A step-up DC/DC converters designed to drive LEDs with a constant current over a wide programmable range. Series connection of the LEDs provides identical LED currents for uniform brightness without the need for ballast resistors and expensive factory calibration.The LT3478-1 reduces external component count and cost by integrating the LED current sense resistor. The LT3478 uses an external sense resistor to extend the maximum programmable LED current beyond 1A and also to achieve greater accuracy when programming low LED currents. Operating frequency can be set with an external resistor from 200kHz up to 2.25MHz. Unique circuitry allows a PWM dimming range up to 3000:1 while maintaining constant LED color. The LT3478/LT3478-1 are ideal for high power LED driver applications such as automotive TFT LCD backlights, courtesy lighting and heads-up displays. One of two CTRL pins can be used to program maximum LED current. The other CTRL pin can be used to program a reduction in maximum LED current vs temperature to maximize LED usage and improve reliability.Additional features include inrush current protection, programmable open LED protection and programmable soft-start. Each part is available in a 16-pin thermally enhanced TSSOP Package.Applications High Power LED Driver Automotive Lighting
LT6402-12 300MHz differential In/Out ADC Driver
Analog Devices Inc.DC954A-B: Demo Board for the LT6402-12 300MHz Low Distortion, Low Noise Differential Amplifier/ADC Driver (AV = 12dB).
LT3844EFE Demo Board | 15V ≤ VIN ≤ 60V, VOUT = 12V @ 4.2A
Analog Devices Inc.Demonstration Circuit 974 is a 100kHz to -500kHz programmable frequency, high voltage, current-mode DC/DC step-down converter featuring the LT3844. The operating frequency can be synchronized up to 600kHz. The board operates from a Vin range of 15V to -60V and outputs 12VOUT @ 4.2A (50W).
LT3476EUHF Demo Board | Quad Buck Mode LED Driver, PVIN ≤ 33V, Up to 27VLED @ 350mA or 1.05A
Analog Devices Inc.Demonstration circuit 976 is a Quadruple High Power LED Driver in Buck Mode featuring the LT3476EUHF. The LT3476 is a quad output, multitopology DC/DC converter designed to operate as a current source for driving high current LEDs. Each of the four regulators on the demo circuit is independently operated. The VIN power supply for the IC ranges from 2.8V to 16V. The PVIN power supply for the buck regulators ranges up to 33V.
On the demo circuit, the default current for each output channel is 350mA but it can be adjusted up to 1.05A via resistor dividers at the VADJ pins. The output current should not exceed the rated current of the LEDs used. If 1W LEDs, such as the Lumileds Luxeon LEDs, are used, 350mA current is the maximum. 1A output current is reserved for 3W LEDs, such as Luxeon III.
The input voltage is limited by the CAP pin overvoltage protection threshold. As a result, each channel of the demo circuit can drive up to 27V total LED voltage.
DC985A-A/B
Analog Devices Inc.The LTC4245 Hot Swap? controller allows a board to be safely inserted and removed from a live backplane in multiple supply systems such as CompactPCI and PCI Express. Using four external N-channel pass transistors, the board supply voltages can be ramped up at an adjustable rate and in any desired sequence. An I2C interface and on-board ADC allow monitoring of board current, voltage and fault status for each supply.The device features adjustable dI/dt controlled soft start and foldback limited inrush current. A dual-level timed circuit breaker and fast current limit protect each supply against overcurrent faults. A power good input with timeout allows a downstream supply monitor to disconnect the board supplies. The device can be con?gured to function without a ?12V supply or with an extra 3.3V supply instead of a 5V supply.The controller has additional features to interrupt the host when a fault has occurred, notify when output power is good, detect insertion of a load card and power-up in either the on or off state.Applications Live Board Insertion CompactPCI, CompactPCI Express, CompactTCA, PCI Express Systems
DC987B-B
Analog Devices Inc.The LTC6400-14 is a high-speed differential amplifier targeted at processing signals from DC to 300MHz. The part has been specifically designed to drive 12-, 14- and 16-bit ADCs with low noise and low distortion, but can also be used as a general-purpose broadband gain block.The LTC6400-14 is easy to use, with minimal support circuitry required. The output common mode voltage is set using an external pin, independent of the inputs, which eliminates the need for transformers or AC-coupling capacitors in many applications. The gain is internally fixed at 14dB (5V/V).The LTC6400-14 saves space and power compared to alternative solutions using IF gain blocks and transformers. The LTC6400-14 is packaged in a compact 16-lead 3mm ? 3mm QFN package and operates over the ?40?C to 85?C temperature range.Applications Differential ADC Driver Differential Driver/Receiver Single Ended to Differential Conversion IF Sampling Receivers SAW Filter Interfacing
LTC6401-8 3GHz Fully Differential ADC Driver Demo Circuit
Analog Devices Inc.DC987B-E: Demo Board for the LTC6401-8 2.2GHz Low Noise, Low Distortion Differential ADC Driver for DC-140MHz.
