DC891A: Demo Board for the LT3750 Capacitor Charger Controller.

DC902A-A: Demo Board for the LTC3214 500mA Camera LED Charge Pump.

The LTC6102/LTC6102HV are versatile, high voltage, highside current sense amplifiers. Their high supply voltage rating allows their use in many high side applications, while the low drift and offset ensure accuracy across a wide range of operating conditions. The LTC6102-1 is a version of the LTC6102 that includes a low power disable mode to conserve system standby power.The LTC6102/LTC6102HV monitor current via the voltage across an external sense resistor (shunt resistor). Internal circuitry converts input voltage to output current, allowing a small sense signal on a large common mode voltage to be translated to a ground-referred signal. Low DC offset allows the use of very low shunt resistor values and large gain-setting resistors. As a result, power loss in the shunt is reduced.The wide operating supply and high accuracy make the LTC6102 ideal for a large array of applications, from automotive, to industrial and power management. A maximum input sense voltage of 2V allows a wide range of currents and voltages to be monitored. Fast response makes the LTC6102 the perfect choice for load current warnings and shutoff protection control.All versions of the LTC6102 are available in 8-lead MSOP and 3mm ? 3mm DFN packages.Applications Current Shunt Measurement Battery Monitoring Remote Sensing Load Protection Motor Control Automotive Controls

The LTC3773 is a high performance, 3-phase, triple output synchronous step-down switching regulator controller with output voltage power up/down tracking capability. The controller allows for sequential, coincident or ratiometric tracking.This 3-phase controller drives its output stages with 120? phase separation at frequencies of up to 700kHz per phase minimizing the RMS input current. Light load efficiency can be maximized by using selectable Burst Mode operation. The 0.6V precision reference supports output voltages from 0.6V to 5V.Fault protection features include output overvoltage, input undervoltage lockout plus current foldback under short-circuit or overload conditions.Applications Servers, Telecom, Industrial Power Supplies General Purpose Multiple Rail DC/DC FPGA and DSP Requirements

DC914B: Demo Board for the LTC3210 MAIN/CAM LED Controller in 3mm × 3mm QFN.

DC918C-B: Demo Board for the LTC2207 16-Bit, 105Msps ADC.

DC918C-C: Demo Board for the LTC2206 16-Bit, 80Msps ADC.

DC918C-E: Demo Board for the LTC2205 16-Bit, 65Msps ADCs.

DC918C-L: Demo Board for the LTC2205-14 14-Bit, 65Msps ADC.

DC919A-F: Demo Board for the LTC2202 16-Bit, 10Msps ADC.

DC919A-J: Demo Board for the LTC2201 16-Bit, 20Msps ADC.

DC920A: Demo Board for the LTC4080 500mA Standalone Li-Ion Charger with Integrated 300mA Synchronous Buck.

Demonstration circuit 927 is a dual output step-down converter featuring the LT3742, a two-phase nonsynchronous buck controller. The demo board operates with a 5.5V to 28V input suppy and provides outputs of 5V@4A and 3.3V@4A.

DC962A-D: Demo Board for the LT6600-15 Very Low Noise, Differential Amplifier and 15MHz Lowpass Filter.

DC968A-D Demo Board for: LT1952 Single Switch Synchronous Forward Controller LTC3900 Synchronous Rectifier Driver for Forward Converters LT4430 Secondary-Side Optocoupler Driver

Demonstration circuit DC970A-A and DC970A-B feature the LTC3541 and LTC3541-1 respectfully, and provide a high efficiency, synchronous buck plus VLDO linear regulator. For the LTC3541, the buck regulator powers up before the linear regular, and for the LTC3541-1, the linear regulator powers up first. The DC970A has an input voltage range of 3.0V to 5.5V. The jumper selectable (2.5V or 1.8V) buck regulator output is capable of delivering up to 500mA of output current; the jumper selectable (0.8V, 1.2V, 1.5V or 1.8V) linear regulator output is capable of delivering up to 300mA of current.

Demonstration circuit 971 is a high current density supply featuring the dual-output, 2-phase synchronous buck regulator LTC3811. The input voltage of the demo board is designed from 4.5V to 14V. The outputs are 2V/15A and 1.5V/15A. The output voltages can be programmed with different start-up tracking modes. All the critical power and controller IC circuits on the DC971 board are within a 1.45” × 0.9” “drop-in” PCB layout space. The outputs can be easily configured to have two separated output voltages or a single high current output voltage with two phases in paralleling.

The LT3482 is a fixed frequency current mode step-up DC/DC converter with voltage doubler designed to bias avalanche photodiodes (APDs) in optical receivers. It can provide up to 90V output. The LT3482 features high side APD bias current monitoring with better than 10% relative accuracy over the entire temperature range. The integrated power switch, Schottky diodes and APD bias current monitor allow a small converter footprint and low solution cost. Constant switching frequency results in predictable output noise that is easy to filter. The inductor-based topology ensures an input free from switching noise. An integrated high side current monitor produces a current proportional to APD bias current with better than 10% relative accuracy over four decades of dynamic range in the input range of 250nA to 2.5mA. This APD bias current can be used as a reference to provide a digitally programmed output voltage via the CTRL pin. The LT3482 is available in the tiny footprint (3mm ? 3mm) 16-lead QFN package.Applications APD Bias PIN Diode Bias Optical Receivers and Modules Fiber Optic Network Equipment

DC987B-C: Demo Board for the LTC6400-20 1.8GHz Low Noise, Low Distortion Differential ADC Driver for 300MHz IF.

DC987B-D: Demo Board for the LTC6400-26 1.9GHz Low Noise, Low Distortion Differential ADC Driver for DC-300MHz.