3 kV RMS Signal and Power Isolated RS-485 Transceiver with 15 kV IEC ESD Features: 3 kV rms isolated RS-485/RS-422 transceiver Low radiated emissions, integrated, isolated dc-to-dc converter Passes EN 55032 Class B with margin on a 2-layer PCB Cable invert smart feature Correct reversed cable connection on A, B, Y, and Z bus pins while maintaining full receiver fail-safe feature ESD protection on RS-485 A, B, Y and Z pins ≥±12 kV IEC61000-4-2 contact discharge ≥±15 kV IEC61000-4-2 air discharge High speed 25 Mbps data rate (ADM2565E/ADM2567E) Low speed 500 kbps data rate for EMI control (ADM2561E/ADM2563E) Flexible power supplies Input VCC supply of 3 V to 5.5 V Logic VIO supply of 1.7 V to 5.5 V VSEL pin to select VISO supply of 5 V (VCC > 4.5 V) or 3.3 V PROFIBUS compliant for 5 V VISO Wide operating temperature range: −40°C to +105°C High common-mode transient immunity: 250 kV/µs Short-circuit, open-circuit, and floating input receiver fail-safe Supports 196 bus nodes (72 kΩ receiver input impedance) Full hot swap support (glitch free power-up/power-down) Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE V 0884-11, UL 1577, CQC11-471543-2012, IEC 61010-1 Complies with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E) 28-lead, fine pitch SOIC_W package (10.15 mm 10.05 mm) with >8.0 mm creepage and clearance

3 kV RMS Signal and Power Isolated RS-485 Transceiver with 15 kV IEC ESD Features: 3 kV rms isolated RS-485/RS-422 transceiver Low radiated emissions, integrated, isolated dc-to-dc converter Passes EN 55032 Class B with margin on a 2-layer PCB Cable invert smart feature Correct reversed cable connection on A, B, Y, and Z bus pins while maintaining full receiver fail-safe feature ESD protection on RS-485 A, B, Y and Z pins ≥±12 kV IEC61000-4-2 contact discharge ≥±15 kV IEC61000-4-2 air discharge High speed 25 Mbps data rate (ADM2565E/ADM2567E) Low speed 500 kbps data rate for EMI control (ADM2561E/ADM2563E) Flexible power supplies Input VCC supply of 3 V to 5.5 V Logic VIO supply of 1.7 V to 5.5 V VSEL pin to select VISO supply of 5 V (VCC > 4.5 V) or 3.3 V PROFIBUS compliant for 5 V VISO Wide operating temperature range: −40°C to +105°C High common-mode transient immunity: 250 kV/µs Short-circuit, open-circuit, and floating input receiver fail-safe Supports 196 bus nodes (72 kΩ receiver input impedance) Full hot swap support (glitch free power-up/power-down) Safety and regulatory approvals (pending) CSA Component Acceptance Notice 5A, DIN V VDE V 0884-11, UL 1577, CQC11-471543-2012, IEC 61010-1 Complies with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E) 28-lead, fine pitch SOIC_W package (10.15 mm 10.05 mm) with >8.0 mm creepage and clearance

3.0 V to 5.5 V, 12 kV IEC ESD Protected, Half Duplex 500 kbps RS-485 Transceiver Features: TIA/EIA RS-485 compliant over full supply range 3.0 V to 5.5 V operating voltage range on VCC 1.62 V to 5.5 V VIO logic supply option available ESD protection on the bus pins IEC 61000-4-2 ±12 kV contact discharge IEC 61000-4-2 ≥ ±12 kV air discharge HBM: ≥ ±30 kV Full hot swap support (glitch free power-up/power-down) High speed 50 Mbps data rate (ADM3065E/ADM3066E/ADM3067E/ADM3068E) Low speed 500 kbps data rate for long cables (ADM3061E/ADM3062E/ADM3063E) Full receiver short-circuit, open circuit, and bus idle fail-safe Extended temperature range up to 125°C PROFIBUS compliant at VCC ≥ 4.5 V Half duplex and full duplex models available Allows connection of up to 128 transceivers onto the bus Space-saving package options 10-lead, 3 mm × 3 mm LFCSP 8-lead and 10-lead, 3 mm × 3 mm MSOP 8-lead and 14-lead, narrow body SOIC

3.0 V to 5.5 V with VIO, 12 kV IEC ESD Protected, Half Duplex 500 kbps RS-485 Transceiver Features: TIA/EIA RS-485 compliant over full supply range 3.0 V to 5.5 V operating voltage range on VCC 1.62 V to 5.5 V VIO logic supply option available ESD protection on the bus pins IEC 61000-4-2 ±12 kV contact discharge IEC 61000-4-2 ≥ ±12 kV air discharge HBM: ≥ ±30 kV Full hot swap support (glitch free power-up/power-down) High speed 50 Mbps data rate (ADM3065E/ADM3066E/ADM3067E/ADM3068E) Low speed 500 kbps data rate for long cables (ADM3061E/ADM3062E/ADM3063E) Full receiver short-circuit, open circuit, and bus idle fail-safe Extended temperature range up to 125°C PROFIBUS compliant at VCC ≥ 4.5 V Half duplex and full duplex models available Allows connection of up to 128 transceivers onto the bus Space-saving package options 10-lead, 3 mm × 3 mm LFCSP 8-lead and 10-lead, 3 mm × 3 mm MSOP 8-lead and 14-lead, narrow body SOIC

3.0 V to 5.5 V with VIO, 12 kV IEC ESD Protected, Half Duplex 500 kbps RS-485 Transceiver Features: TIA/EIA RS-485 compliant over full supply range 3.0 V to 5.5 V operating voltage range on VCC 1.62 V to 5.5 V VIO logic supply option available ESD protection on the bus pins IEC 61000-4-2 ±12 kV contact discharge IEC 61000-4-2 ≥ ±12 kV air discharge HBM: ≥ ±30 kV Full hot swap support (glitch free power-up/power-down) High speed 50 Mbps data rate (ADM3065E/ADM3066E/ADM3067E/ADM3068E) Low speed 500 kbps data rate for long cables (ADM3061E/ADM3062E/ADM3063E) Full receiver short-circuit, open circuit, and bus idle fail-safe Extended temperature range up to 125°C PROFIBUS compliant at VCC ≥ 4.5 V Half duplex and full duplex models available Allows connection of up to 128 transceivers onto the bus Space-saving package options 10-lead, 3 mm × 3 mm LFCSP 8-lead and 10-lead, 3 mm × 3 mm MSOP 8-lead and 14-lead, narrow body SOIC

3.0 V to 5.5 V with VIO, 12 kV IEC ESD Protected, Half Duplex 500 kbps RS-485 Transceiver Features: TIA/EIA RS-485 compliant over full supply range 3.0 V to 5.5 V operating voltage range on VCC 1.62 V to 5.5 V VIO logic supply option available ESD protection on the bus pins IEC 61000-4-2 ±12 kV contact discharge IEC 61000-4-2 ≥ ±12 kV air discharge HBM: ≥ ±30 kV Full hot swap support (glitch free power-up/power-down) High speed 50 Mbps data rate (ADM3065E/ADM3066E/ADM3067E/ADM3068E) Low speed 500 kbps data rate for long cables (ADM3061E/ADM3062E/ADM3063E) Full receiver short-circuit, open circuit, and bus idle fail-safe Extended temperature range up to 125°C PROFIBUS compliant at VCC ≥ 4.5 V Half duplex and full duplex models available Allows connection of up to 128 transceivers onto the bus Space-saving package options 10-lead, 3 mm × 3 mm LFCSP 8-lead and 10-lead, 3 mm × 3 mm MSOP 8-lead and 14-lead, narrow body SOIC

30 V, Micropower, Overvoltage Protection, Rail-to-Rail Input/Output Quad Op Amplifier Features: Input overvoltage protection, 32 V above and below the supply rails No phase reversal for input voltage up to ±32 V beyond the power supply Rail-to-rail input and output swing Low power: 60 μA per amplifier typical Unity-gain bandwidth 800 kHz typical at VSY = ±15 V 550 kHz typical at VSY = ±5 V 465 kHz typical at VSY = ±1.5 V Single-supply operation: 3 V to 30 V Low offset voltage: 300 μV maximum Large signal voltage gain: 120 dB typical Unity gain stable Qualified for automotive applications

50 V, 8 MHz, 1.5 mA per Channel, Robust, Over-The-Top, Precision Op Amps Features: Ultrawide common-mode range: −VS − 0.1 V to −VS + 70 V Wide power supply voltage range: (VSY): +3.15 V to +50 V (±25 V for PSRR) Low supply current: 1.5 mA per channel (typical) Low input offset voltage: ±40 μV maximum Low input offset voltage drift: ±0.4 μV/°C maximum Low voltage noise: 1/f noise corner: 6 Hz typical 150 nV p-p typical at 0.1 Hz to 10 Hz 7 nV/√Hz typical at 100 Hz (en) High speed GBP: 8 MHz typical Slew rate: 5.5 V/μs typical at ΔVOUT = 25 V Low power shutdown: 20 μA maximum Low input bias current: ±10 nA maximum Large signal voltage gain: 120 dB minimum CMRR: 118 dB, minimum PSRR: 123 dB, minimum Input overdrive tolerant with no phase reversal ±2 kV HBM and ±1.25 kV FICDM Wide temperature range: −55°C to +150°C (H grade)

OVP and EMI Protected, Precision, Low Noise and Bias Current Quad Op Amp Features: Low offset voltage: 60 μV maximum at 25°C (8-lead and 14-lead SOIC) Low offset voltage drift: 1 μV/°C maximum (8-lead and 14-lead SOIC) Low input bias current: 1 nA maximum at 25°C Low voltage noise density: 8 nV/√Hz typical at 1 kHz Large signal voltage gain (AVO): 100 dB minimum over full supply voltage and operating temperature Input overvoltage protection to 32 V above and below the supply voltage rail Integrated EMI filter 70 dB typical rejection at 1000 MHz 90 dB typical rejection at 2400 MHz Rail-to-rail output swing Low supply current: 500 μA typical per amplifier Wide bandwidth Gain bandwidth product (AV = 100): 3.5 MHz typical Unity-gain crossover (AV = 1): 3.5 MHz typical −3 dB bandwidth (AV = 1): 6 MHz typical Dual-supply operation Specified at ±5 V to ±15 V, operates over ±2.5 V to ±18 V Unity-gain stable No phase reversal Long-term offset voltage drift (10,000 hours): 2 μV typical Temperature hysteresis: 2 μV typical

Zero Drift, High Voltage, Low Power, Programmable Gain Instrumentation Amplifier Features: Optimized for ADC synchronization Low power: 22 mW (±12 V supplies) 12 binary gain steps from 1/16 V/V to 128 V/V 3 scaling gains: 1 V/V, 1.25 V/V, and 1.375 V/V ±60 V protected input multiplexer Excellent dc precision Low input offset voltage: ±14 μV maximum Low input offset voltage drift: ±0.08 μV/°C maximum Gain calibration via ROM Low gain drift: ±1 ppm/°C maximum High CMRR: 116 dB minimum, G = 1 V/V Low input bias current: ±1.5 nA maximum High input impedance Integrated input EMI filtering Wide input supply range: ±5 V to ±28 V Dedicated output amplifier supplies 7 GPIO ports with special functions Sequential chip select mode External multiplexer control Excitation current sources SPI port with checksum (CRC) support Internal fault detection Wire break test currents On-chip test multiplexer 28-lead, 5 mm × 5 mm LFCSP, 24-lead TSSOP Specified temperature range: −40°C to +105°C

Zero Drift, High Voltage, Low Power, Programmable Gain Instrumentation Amplifier Features: Optimized for ADC synchronization Low power: 22 mW (±12 V supplies) 12 binary gain steps from 1/16 V/V to 128 V/V 3 scaling gains: 1 V/V, 1.25 V/V, and 1.375 V/V ±60 V protected input multiplexer Excellent dc precision Low input offset voltage: ±14 μV maximum Low input offset voltage drift: ±0.08 μV/°C maximum Gain calibration via ROM Low gain drift: ±1 ppm/°C maximum High CMRR: 116 dB minimum, G = 1 V/V Low input bias current: ±1.5 nA maximum High input impedance Integrated input EMI filtering Wide input supply range: ±5 V to ±28 V Dedicated output amplifier supplies 7 GPIO ports with special functions Sequential chip select mode External multiplexer control Excitation current sources SPI port with checksum (CRC) support Internal fault detection Wire break test currents On-chip test multiplexer 28-lead, 5 mm × 5 mm LFCSP, 24-lead TSSOP Specified temperature range: −40°C to +105°C

Zero Drift, High Voltage, Low Power, Programmable Gain Instrumentation Amplifier Features: Optimized for ADC synchronization Low power: 22 mW (±12 V supplies) 12 binary gain steps from 1/16 V/V to 128 V/V 3 scaling gains: 1 V/V, 1.25 V/V, and 1.375 V/V ±60 V protected input multiplexer Excellent dc precision Low input offset voltage: ±14 μV maximum Low input offset voltage drift: ±0.08 μV/°C maximum Gain calibration via ROM Low gain drift: ±1 ppm/°C maximum High CMRR: 116 dB minimum, G = 1 V/V Low input bias current: ±1.5 nA maximum High input impedance Integrated input EMI filtering Wide input supply range: ±5 V to ±28 V Dedicated output amplifier supplies 7 GPIO ports with special functions Sequential chip select mode External multiplexer control Excitation current sources SPI port with checksum (CRC) support Internal fault detection Wire break test currents On-chip test multiplexer 28-lead, 5 mm × 5 mm LFCSP, 24-lead TSSOP Specified temperature range: −40°C to +105°C

36 V, Low Noise, Zero Drift Op Amp Features: Supply voltage range: 4.5 V to 36 V Offset voltage: ±4 µV maximum at 5 V Offset voltage drift: 0.01 µV/°C maximum at 5 V Input noise Voltage: 88 nV p-p from 0.1 Hz to 10 Hz typical Spectral density voltage: 4.2 nV/√Hz typical at 1 kHz Rail-to-rail output Unity-gain stable GBP: 5 MHz typical Slew rate: 1.8 V/µs typical falling PSRR: 168 dB typical at VS = 4.5 V to 36 V Open-loop voltage gain: 160 dB typical at VOUT = −14.75 V to +14.75 V, RL = 10 k, VS = 30 V CMRR: 160 dB typical at VCM = −15.1 V to +13.5 V,VS= 30V Integrated EMI filters Shutdown mode Ground sense Available in 8-lead SOIC, 8-lead MSOP, and 8-lead LFCSP

16-Bit, 15 MSPS, Module Data Acquisition Solution Features: Integrated fully differential ADC driver with signal scaling Wide input common range High common-mode rejection Single-ended to differential conversion 2.048 V input range with 4.096 V REFBUF Critical passive components 0.005% precision matched resistor array for FDA 9 mm × 9 mm, 0.8 mm pitch, 100-ball BGA package 4× footprint reduction versus discrete solution Low power, dynamic power scaling, power-down mode 143 mW typical at 15 MSPS Throughput: 15 MSPS, no pipeline delay INL: 0.4 LSB typical, 1 LSB maximum SINAD: 89 dB typical at 1 kHz THD: 115 dB at 1 kHz, 106 dB at 400 kHz Gain error: 0.005% FS typical Gain error drift: 1 ppm/C maximum On-board reference buffer with VCMO generation Serial LVDS interface Wide operating temperature range: 40C to +85C

0.5 GHz to 19 GHz Broadband Bi-Directional Single Channel True Time Delay Unit Features:0.5 GHz to 19 GHz frequency rangeProgrammable Time Delay: 7-bit resolutionProgrammable Time Delay ModesTD_Mode0: 0 to 508ps range, 4ps Standard resolutionTD_Mode1: 0 to 254ps range, 2ps High resolutionProgrammable Attenuation: 6-bit resolution31.5 dB adjustment range0.5 dB step sizeFully programmable via a 3-wire or 4-wire SPI interfaceSPI Programmable and Daisy Chaining selectablePower Dissipation: 1 mW with 1.2V and 1.0V Dual Supplies14-pin 2x3mm LFCSP

SigmaDSP Digital Audio Processor Features: Qualified for automotive applications Fully programmable audio DSP for enhanced sound processing Features SigmaStudio, a proprietary graphical programming tool for the development of custom signal flows Clock oscillator for generating master clock from crystal Up to 294.912 MHz, 32-bit SigmaDSP core at 1.2 V Up to 6144 SIMD instructions per sample at 48 kHz Up to 40 kWords of parameter/data RAM Up to 800 ms digital audio delay pool at 48 kHz Audio input/output and routing 4 serial input ports, 4 serial output ports 48-channel, 32-bit digital input/output up to a sample rate of 192 kHz Flexible configuration for TDM, I2S, left and right justified formats, and PCM Up to 8 stereo ASRCs from 1:8 up to 7.75:1 ratio and 139 dB DNR Stereo S/PDIF input and output Four PDM microphone input channels Multichannel, byte addressable, TDM serial ports Integer PLL and flexible clock generators Integrated die temperature sensor

Low Power, Low Noise and Distortion, Rail-to-Rail Output Amplifier Features: Low power: 1.1 mA/amp Low wideband noise 2.1 nV/√Hz 1.4 pA/√Hz Low 1/f noise 7 nV/√Hz @ 10 Hz 13 pA/√Hz @ 10 Hz Low distortion: −105 dBc @ 100 kHz, VO = 2 V p-p High speed 80 MHz, −3 dB bandwidth (G = +1) 12 V/μs slew rate 175 ns settling time to 0.1% Low offset voltage: 0.3 mV maximum Rail-to-rail output Power down Wide supply range: 2.7 V to 12 V

High Efficiency Battery Charger/USB Power Manager Features: Switching Regulator Makes Optimal Use of Limited Power Available from USB Port to Charge Battery  and Power Application 180mΩ Internal Ideal Diode Plus Optional External Ideal Diode Controller Seamlessly Provides Low  Loss Power Path When Input Power is Limited or  Unavailable Full Featured Li-Ion/Polymer Battery Charger VBUS Operating Range: 4.25V to 5.5V (7V Absolute  Maximum—Transient) 1.2A Maximum Input Current Limit 1.5A Maximum Charge Current with Thermal Limiting Bat-Track Adaptive Output Control Slew Control Reduces Switching EMI Low Profile (0.75mm) 14-Lead 4mm × 3mm DFN Package

Micropower Low Noise Boost Converters with Output Disconnect Features: Low Quiescent Current 65µA in Active Mode 1µA in Shutdown Mode Switching Frequency is Non-Audible Over Entire Load Range Integrated Power NPN: 350mA Current Limit (LT3494A) 180mA Current Limit (LT3494) Integrated Schottky Diode Integrated Output Disconnect Integrated Output Dimming Wide Input Range: 2.3V to 16V Wide Output Range: Up to 40V Tiny 8-Lead 3mm × 2mm DFN Package

2.25MHz, 800mA Synchronous Step-Down Regulator in ThinSOT Features: High Efficiency: Up to 95% Low Output Ripple (<20mVP-P): Burst Mode® Operation: IQ = 16µA 2.5V to 5.5V Input Voltage Range 2.25MHz Constant Frequency Operation Synchronizable to External Clock No Schottky Diode Required Stable with Ceramic Capacitors Low Dropout Operation: 100% Duty Cycle 0.6V Reference Allows Low Output Voltages Shutdown Mode Draws < 1µA Supply Current ±2% Output Voltage Accuracy Current Mode Operation for Excellent Line and Load Transient Response Overtemperature Protected Low Profile (1mm) ThinSOT™ Package