4-Channel, Low Noise, Low Power, 24-Bit, Sigma-Delta ADC with PGA and Reference Features: Three power modes RMS noise Low power: 24 nV rms at 1.17 SPS, gain = 128 (255 μA typical) Mid power: 20 nV rms at 2.34 SPS, gain = 128 (355 μA typical) Full power: 23 nV rms at 9.4 SPS, gain = 128 (930 μA typical) Up to 22 noise free bits in all power modes (gain = 1) Output data rate Full power: 9.38 SPS to 19,200 SPS Mid power: 2.34 SPS to 4800 SPS Low power: 1.17 SPS to 2400 SPS Rail-to-rail analog inputs for gains > 1 Simultaneous 50 Hz/60 Hz rejection at 25 SPS (single cycle settling) Diagnostic functions (which aid safe integrity level (SIL) certification Crosspoint multiplexed analog inputs 4 differential/7 pseudo differential inputs Programmable gain (1 to 128) Band gap reference with 10 ppm/°C drift maximum (70 μA) Matched programmable excitation currents Internal clock oscillator On-chip bias voltage generator Low-side power switch General-purpose outputs Multiple filter options Internal temperature sensor Self and system calibration Sensor burnout detection Automatic channel sequencer Per channel configuration Power supply: 2.7 V to 3.6 V and ±1.8 V Independent interface power supply Power-down current: 5 μA maximum Temperature range: −40°C to +125°C 32-lead LFCSP/24-lead TSSOP 3-wire or 4-wire serial interface SPI, QSPI, MICROWIRE, and DSP compatible Schmitt trigger on SCLK ESD: 4 kVAD7124-4-EP Supports defense and aerospace applications (AQEC standard) Download AD7124-4-EP Data Sheet (PDF) Full military temperature range: −55°C to +125°C Controlled manufacturing baseline 1 assembly/test site 1 fabrication site Product change notification Qualification data available on request V62/19614

Precision Analog Front End and Controller for Battery Test/Formation Systems Features: Integrated constant current and voltage modes with automatic switchover Charge and Discharge modes Precision voltage and current measurement Integrated precision control feedback blocks Precision interface to PWM or linear power converters Programmable gain settings Current sense gains: 26, 66, 133, 200 Voltage sense gains: 0.2, 0.27, 0.4, 0.8 Programmable OVP, OCP fault detection Current sharing & balancing Excellent ac & dc performance See datasheet for additional features

Low Cost 270 MHz Differential Receiver Amplifier Features: High Speed AD8130: 270 MHz, 1090 V/µs @ G = +1 AD8129: 200 MHz, 1060 V/µs @ G = +10 High CMRR 94 dB min, dc to 100 kHz 80 dB min @ 2 MHz 70 dB @ 10 MHz Low noise AD8130: 12.5 nV/√Hz AD8129: 4.5 nV/√Hz High input impedance: 1 MΩ differential Input common-mode range ±10.5 V Low distortion, 1 V p-p @ 5 MHz: AD8130, -79 dBc worst harmonic @ 5 MHz AD8129, -74 dBc worst harmonic @ 5 MHz User-adjustable gain No external components for G = +1 Power supply range +4.5 V to ±12.6 V Power-down

GaAs MMIC SP4T Non-Reflective Switch, DC - 3.5 GHz Features: RoHS Compliant Product Low Insertion Loss (2 GHz): 0.7 dB Single Positive Supply: VDD = +5V Integrated 2:4 TTL Decoder 16 Lead QSOP Package

Quad, 16-Bit nanoDAC with 5ppm/C On-Chip Reference Features: Low power, smallest pin-compatible, quad nanoDACs  AD5664R: 16 bits AD5644R: 14 bits AD5624R: 12 bits User selectable external or internal reference External reference default On-chip 1.25 V/2.5 V, 5 ppm/°C reference 10-lead MSOP; 10-lead, 3 mm × 3 mm LFCSP_WD; and 12-ball, 1.665 mm × 2.245 mm WLCSP 2.7 V to 5.5 V power supply Guaranteed monotonic by design Power-on reset to zero scale Per channel power-down Serial interface, up to 50 MHz

Single and Multichannel, Synchronous Voltage-to-Frequency Converters Features: AD7741: One Single-Ended Input Channel AD7742: Two Differential or Three Pseudo-Differential Input Channels Integral Nonlinearity of 0.012% at fOUT(Max) = 2.75 MHz (AD7742) and at fOUT(Max) = 1.35 MHz (AD7741) Single +5 V Supply Operation Buffered Inputs Programmable Gain Analog Front-End On-Chip +2.5 V Reference Internal/External Reference Option Power Down to 35 µA Max Minimal External Components Required 8-Lead and 16-Lead DIP and SOIC Packages

Dual Differential 16-Bit, 1 MSPS PulSAR 12.0 mW in QSOP Features: 16-bit resolution with no missing codes Throughput: 1 MSPS Low power dissipation 7.0 mW at 1 MSPS (VDD1 and VDD2 only) 12.0 mW at 1 MSPS (total) 140 µW at 10 kSPS INL: ±0.5 LSB typical, ±2.0 LSB maximum True differential analog input range: ±VREF 0 V to VREF with VREF between 2.4 V to 5.1 V Allows use of any input range Easy to drive with the ADA4941-1 SINAD: 93.5 dB at 1 kHz THD: −112 dB at 1 kHz No pipeline delay Single-supply 2.5 V operation with 1.8 V/2.5 V/3 V/5 V logic interface Serial interface SPI/QSPI/MICROWIRE/DSP compatible 20-lead QSOP package Wide operating temperature range: −40°C to +125°C

18-Bit, 5 MSPS PULSAR Differential ADC Features: Throughput: 5 MSPS 18-bit resolution with no missing codes SNR 99 dB INL +/-0.8 LSB DNL +/-0.5 LSB True differential analog input voltage range: ±4.096 V or ±5 V Low power dissipation (39 mW) SAR architecture External reference options Serial LVDS interface 32-lead, 5mm × 5mm LFCSP (QFN) See datasheet for more details

Ultrafast 3.3 V Single-Supply Comparator w/CML Output Drivers Features: 3.3 V/5.2 V single-supply operation 150 ps propagation delay 15 ps overdrive and slew rate dispersion 8 GHz equivalent input rise time bandwidth 80 ps minimum pulse width 35 ps typical output rise/fall 10 ps deterministic jitter (DJ) 200 fs random jitter (RJ) On-chip terminations at both input pins Robust inputs with no output phase reversal Resistor-programmable hysteresis Differential latch control Extended industrial −40°C to +125°C temperature range

High Performance Narrowband ISM Transceiver IC Features: Low power, high performance, narrowband transciever Frequency Bands: 80-650MHz and 862-940MHz Modulation schemes: 2FSK, 3FSK, 4FSK Spectral shaping: Gaussian and Raised Cosine Filtering Automatic PA ramp Data rates supported: 0.05kps to 25kbps Programmable output power: –16dBm to +13dBm Low IF architecture with programmable IF bandwidths of 12.5/18.5/25kHz 2.3V to 3.6V Power Supply Receiver sensitivity: –123dBm @ 1kbps FSK Fully automatic frequency control loop (AFC) compensates for lower tolerance crystals High Accuracy digital RSSI and integrated Tx/Rx switch

Single/Dual-Supply High-Voltage Isolated IGBT Gate Driver with Miller Clamp Features: 13 A short-circuit source current (0 Ω gate resistance) 14 A short-circuit sink current (0 Ω gate resistance) 4.61 A peak current (2 Ω gate resistance) Output power device resistance: <1 Ω Desaturation protection Isolated desaturation fault reporting Soft shutdown on fault Miller clamp output with gate sense input Isolated fault and ready functions Low propagation delay: 55 ns typical Minimum pulse width: 50 ns Operating temperature range: −40°C to +125°C Output voltage range to 30 V Input voltage range from 2.5 V to 6 V Output and input undervoltage lockout (UVLO) Creepage distance: 7.8 mm minimum 100 kV/μs common-mode transient immunity (CMTI) 20-year lifetime for 600 V rms or 1092 V dc working voltage Safety and regulatory approvals 5 kV ac for 1 minute per UL 1577 CSA Component Acceptance Notice 5A DIN VDE V 0884-11:2017-01 VIORM = 849 V peak (reinforced) Qualified for automotive applications

High Temperature, 16-Bit, 600 kSPS PulSAR ADC Features: Download AD7981-KGD Data Sheet. Available as Known Good Die and fully guaranteed to data sheet specifications. Extreme high temperature operation Specified temperature range −55°C to +210°C (10-lead FLATPACK) −55°C to +175°C (10-Lead MSOP) High performance Pseudo differential analog input range 0 V to VREF with VREF between 2.4 V and 5.1 V Throughput: 600 kSPS Zero latency architecture 16-bit resolution with no missing codes INL: ±2.5 LSB maximum, DNL: ±0.9 LSB maximum Dynamic range: 92 dB, VREF = 5 V SNR: 91 dB at fIN = 1 kHz, VREF = 5 V THD: −102 dB at fIN = 1 kHz, VREF = 5 V SINAD: 90.5 dB at fIN = 1 kHz, VREF = 5 V Low power dissipation Single-supply 2.5 V operation with 1.8 V to 5 V logic interface 2.25 mW typical at 600 kSPS (VDD only) 4.65 mW typical at 600 kSPS (total) 75 μW typical at 10 kSPS Proprietary serial interface SPI-/QSPI-/MICROWIRE-/DSP-compatible Daisy-chain multiple ADCs and busy indicator Small footprint 10-lead, 3 mm × 3 mm, monometallic wire bonding MSOP 110-lead, 0.255 inches × 0.255 inches, monometallic wire bonding FLATPACK

GaAs pHEMT MMIC Low Noise Amplifier, 700 - 1000 MHz Features:Noise Figure: Output IP3: +34 dBmGain: 15 dBVery Stable Gain vs. Supply & TemperatureSingle Supply: +5V @ 100 mA50 Ohm Matched Output

Active Bias Controller Features: Automatic Gate voltage adjustment (No Calibration required) Supply Voltage: 4V to 12V Digital Voltage: 3.3V to 5V Controls both Enhancement and Depletion type devices Adjustable Drain Current up to 200mA Sink/Source Gate Current Capability Optional Internal negative voltage generation that can be disabled to use external negative rail Fast Enable/Disable Trigger-out Output for Daisy Chain Power-Up and Power-Down Sequencing

Hot Swap Controller with Multifunction Current Control Features: Allows Safe Board Insertion and Removal from a Live Backplane Controls Supply Voltages from 2.5V to 16.5V Programmable Soft-Start with Inrush Current Limiting, No External Gate Capacitor Required Faster Turn-Off Time Because No External Gate Capacitor is Required Dual Level Overcurrent Fault Protection Programmable Response Time for Overcurrent Protection (MS) Programmable Overvoltage Protection (MS) Automatic Retry or Latched Mode Operation (MS) High Side Drive for an External N-Channel FET User-Programmable Supply Voltage Power-Up Rate FB Pin Monitors VOUT and Signals RESET Glitch Filter Protects Against Spurious RESET Signal

LTC2260-14 series 14 Bit 105M Samples per Second Analog to Digital Converter (ADC) Evaluation Board

SiGe or InGaP, HBT Gain Block Amplifier SMT, DC to 5 GHz Features: P1dB Output Power: +19 dBm Gain: 20 dB Output IP3: +33 dBm Cascadable 50 Ohm I/Os Single Supply: +6V to +12V Industry Standard SOT89 Package Included in the HMC-DK001 Designer’s Kits

70 dB, Logarithmic Detector/Controller SMT, 1 - 8000 MHz Features: Wide Dynamic Range: up to 70 dB High Accuracy: ±1 dB with 60 dB Range Up To 6 GHz Fast: 10ns Output Response Time Supply Voltage: +5V Power-Down Mode Excellent Stability over Temperature Buffered Temperature Sensor Output 4x4mm Leadless SMT Package

Single/Dual, +15 V/5 V, 256-Position, I2C-Compatible Digital Potentiometer Features:AD5280: 1 channelAD5282: 2 channels256 positions+10 V to +15 V single supply; 5.5 V dual-supply operationFixed terminal resistance: 20 k, 50 k, 200 kLow temperature coefficient: 30 ppm/CPower-on midscale preset1 Programmable resetOperating temperature: 40°C to +85°CI2C-compatible interface

2-Channel, 2.35 V to 5.25 V, 1 MSPS, 12-Bit A/D Converter Features: Fast Throughput Rate: 1 MSPS Specified for VDD of 2.35 V to 5.25 V Low Power: 4.8 mW typ at 1 MSPS with 3 V Supplies 15.5 mW typ at 1 MSPS with 5 V Supplies Wide Input Bandwidth: 71.4 dB min SNR at 100 kHz Input Frequency Flexible Power/Serial Clock Speed Management No Pipeline Delays High Speed Serial Interface SPI®/QSPI™/MICROWIRE™/DSP Compatible Standby Mode: 1 µA max Daisy Chain Mode 8-Lead TSOT Package 8-Lead MSOP Package