ARDUINO MKR MOTOR CARRIER;

MKR WAN 1300 is a powerful board that combines the functionality of the MKR Zero and LoRa connectivity. It is the ideal solution for makers wanting to design IoT projects with minimal previous experience in networking having a low power device. Arduino MKR WAN 1300 has been designed to offer a practical and cost effective solution for makers seeking to add Lo-Ra connectivity to their projects with minimal previous experience in networking. It is based on the Atmel SAMD21 and a Murata CMWX1ZZABZ Lo-Ra module. The design includes the ability to power the board using two 1.5V AA or AAA batteries or external 5V. Switching from one source to the other is done automatically. A good 32 bit computational power similar to the MKR ZERO board, the usual rich set of I/O interfaces, low power Lo-Ra communication and the ease of use of the Arduino Software (IDE) for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power (5V) to the board. The Arduino MKR WAN 1300 is able to run with or without the batteries connected and has limited power consumption. Warning: Unlike most Arduino & Genuino boards, the MKR WAN 1300 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.

With the MKR Vidor 4000 you can configure it the way you want; you can essentially create your own controller board. It comes loaded with hardware and potential: an 8 MB SRAM; a 2 MB QSPI Flash chip — 1 MB allocated for user applications; a Micro HDMI connector; an MIPI camera connector; and Wifi & BLE powered by U-BLOX NINA W10 Series. It also includes the classic MKR interface on which all pins are driven both by SAMD21 and FPGA. Plus, it has a Mini PCI Express connector with up to 25 user programmable pins. The FPGA contains 16K Logic Elements, 504 KB of embedded RAM, and 56 18x18 bit HW multipliers for high-speed DSP. Each pin can toggle at over 150 MHz and can be configured for functions such as UARTs, (Q)SPI, high resolution/high frequency PWM, quadrature encoder, I2C, I2S, Sigma Delta DAC, etc. The on-board FPGA can be also used for high-speed DSP operations for audio and video processing. This board also features a Microchip SAMD21. Communication between FPGA and the SAMD21 is seamless.

Arduino Ethernet shield 2 without POE. Technology: Development Board. Processor Type: MCU. MPN: A000024

NANO 33 BLE DEV BRD, ARM CORTEX-M4F MCU; Silicon Manufacturer:Nordic Semiconductor; No. of Bits:32bit; Silicon Family Name:-; Core Architecture:ARM; Core Sub-Architecture:Cortex-M4F; Silicon Core Number:nRF52840; Product Range:- RoHS Compliant: Yes

NANO 33 BLE W/HEADER DEVELOPMENT BOARD; Silicon Manufacturer:Nordic Semiconductor; No. of Bits:32bit; Silicon Family Name:-; Core Architecture:ARM; Core Sub-Architecture:Cortex-M4F; Silicon Core Number:nRF52840; Product Range:- RoHS Compliant: Yes

TINKERKIT BRACCIO ROBOTIC ARM;

ATmega32U4 Arduino Micro series AVR MCU 8-Bit Embedded Evaluation Board

The Arduino GIGA R1 WiFi is designed for ambitious makers who want to step up their game. It levels the playing field for gamers, artists, sound designers and anyone coming to the tech world with big ideas on a budget – because it packs advanced features into an accessible component, with the same form factor as our popular Mega and Due. Let’s break down all the powerful features of this board. Microcontroller (STM32H747XI): This dual core 32-bits microcontroller allows you have two brain talking to each other (a Cortex-M7 at 480 MHz and a Cortex-M4 at 240 MHz) you can even run micropython in one and Arduino in the other. Wireless communication (Murata 1DX):  Whether you prefer Wi-Fi or Bluetooth, the GIGA R1 WiFi got you covered. You can even quickly connect to the Arduino IoT Cloud and keep track of your project remotely. And if you are concerned about the security of the communication, the ATECC608A keeps everything under control. Hardware ports and communication: Following the legacy of the Arduino Mega and the Arduino Due, the GIGA R1 WiFi has 4 UARTs (hardware serial ports), 3 I2C ports (1 more than its predecessors), 2 SPI ports (1 more than its predecessors), 1 FDCAN. GPIOs and extra pins: We wanted to keep the same form factor of the Mega and the Due, so you can easily adapt your custom made shields to the GIGA R1 WiFi (remember this board works at 3.3V though!) and we added extra headers to access extra pins, leaving the total count to 76 GPIO pins, and the best part, you can access them from underneath, so keep your project as it is and just think on how to expand it. Also, we added two new pins: a VRTC so you can connect a battery to keep the RTC running while the board is off and an OFF pin so you can shut down the board. Connectors: The GIGA R1 WiFi has extra connectors on board which will facilitate the creation of your project without any extra hardware. This board has: USB-A connector suitable for hosting USB sticks, other mass storage devices and HID devices such as keyboard or mouse. 3.5mm input-output jack connected to DAC0, DAC1 and A7. USB-C® to power and program the board, as well as simulate an HID device such as mouse or keyboard. Jtag connector, 2x5 1.27mm. 20 pin Arducam camera connector. Higher voltage support: In comparison with its predecessors that support up to 12 volts, the GIGA R1 WiFi can handle a range of 6 to 24 volts.  

Arduino Nano 33 BLE Sense Rev2 with headers An AI (Artificial Intelligence) enabled board in the shape of the classic Nano board, with all the sensors to start building your next project right away. The Arduino Nano 33 BLE Sense Rev2 with headers is Arduino’s 3.3V AI enabled board in the smallest available form factor with a set of sensors that will allow you without any external hardware to start programming your next project, right away. With the Arduino Nano 33 BLE Sense Rev2, you can: Build wearable devices that using AI can recognize movements. Build a room temperature monitoring device that can suggest or modify changes in the thermostat. Build a gesture or voice recognition device using the microphone or the gesture sensor together with the AI capabilities of the board. The main feature of this board, besides the complete selection of sensors, is the possibility of running Edge Computing applications (AI) on it using TinyML. Learn how to use the Tensor Flow Lite library following this instructions or learn how to train your board using Edge Impulse. Tech Specs Microcontroller - nRF52840 Operating Voltage - 3.3V Input Voltage - 21V DC Current per I/O Pin - 15mA Clock Speed - 64MHz CPU Flash Memory - 1MB (nRF52840) SRAM - 256KB (nRF52840) EEPROM - none Digital Input / Output Pins - 14 PWM Pins - All digital pins UART - 1 SPI - 1 I2C - 1 Analog Input Pins - 8 (ADC 12 bit 200 k samples) Analog Output Pins - Only through PWM (no DAC) External Interrupts - All digital pins LED_BUILTIN - 13 USB - Native in the nRF52840 Processor IMU - BMI1270 and BMM150 Microphone - MP34DT06JTR Gesture, light, proximity, color - APDS9960 Barometric pressure - LPS22HB Temperature, humidity - HS3003

DEVELOPMENT BOARD, 32BIT, XTENSA LX7; Key Features: Tiny footprint: Designed with the well-known Nano form factor in mind, this board's compact size makes it perfect for embedding in standalone projects. Wi-Fi and Bluetooth: Harness the power of the ESP32-S3 microcontroller, well-known in the IoT realm, with full Arduino support for wireless and Bluetooth connectivity. Arduino and MicroPython support: Seamlessly switch between Arduino and MicroPython programming with a few simple steps. Arduino even offer an introductory course for those new to the MicroPython world. Arduino IoT Cloud compatible: Quickly and easily create IoT projects with just a few lines of code. Our setup takes care of security, allowing you to monitor and control your project from anywhere using the Arduino IoT Cloud app. (Available starting August 2023) HID support: Emulate human interface devices, such as keyboards or mice, over USB, opening up new possibilities for interacting with your computer. Tech Specs: Board Name Arduino® Nano ESP32 with headers SKU ABX00083 Microcontroller u-blox® NORA-W106 (ESP32-S3) USB connector USB-C® Pins Built-in LED Pin 13 Built-in RGB LED pins 14-16 Digital I/O Pins 14 Analog input pins 8 PWM pins 5 External interrupts All digital pins Connectivity Wi-Fi® u-blox® NORA-W106 (ESP32-S3) Bluetooth® u-blox® NORA-W106 (ESP32-S3) Communication UART 2x I2C 1x, A4 (SDA), A5 (SCL) SPI D11 (COPI), D12 (CIPO), D13 (SCK). Use any GPIO for Chip Select (CS) Power I/O Voltage 3.3 V Input voltage (nominal) 6-21 V Source Current per I/O Pin 40 mA Sink Current per I/O Pin 28 mA Clock speed Processor up to 240 MHz Memory ROM 384 kB SRAM 512 kB External Flash 128 Mbit (16 MB) Dimensions Width 18 mm Length 45 mm

Arduino Nano ESP32 Introducing the Nano ESP32, a powerful addition to the Arduino ecosystem that brings the popular ESP32-S3 to the world of Arduino and MicroPython programming. Whether you're a beginner stepping into the world of IoT or MicroPython, or an advanced user looking to incorporate it into your next product, the Nano ESP32 is the perfect choice. It covers all your needs to kick-start your IoT or MicroPython project with ease. Key Features: Tiny footprint: Designed with the well-known Nano form factor in mind, this board's compact size makes it perfect for embedding in standalone projects. Wi-Fi and Bluetooth: Harness the power of the ESP32-S3 microcontroller, well-known in the IoT realm, with full Arduino support for wireless and Bluetooth connectivity. Arduino and MicroPython support: Seamlessly switch between Arduino and MicroPython programming with a few simple steps. Arduino even offer an introductory course for those new to the MicroPython world. Arduino IoT Cloud compatible: Quickly and easily create IoT projects with just a few lines of code. Our setup takes care of security, allowing you to monitor and control your project from anywhere using the Arduino IoT Cloud app. (Available starting August 2023) HID support: Emulate human interface devices, such as keyboards or mice, over USB, opening up new possibilities for interacting with your computer. Tech Specs: Board Name Arduino Nano ESP32 SKU ABX00092 Microcontroller u-blox NORA-W106 (ESP32-S3) USB connector USB-C Pins Built-in LED Pin 13 Built-in RGB LED pins 14-16 Digital I/O Pins 14 Analog input pins 8 PWM pins 5 External interrupts All digital pins Connectivity Wi-Fi u-blox NORA-W106 (ESP32-S3) Bluetooth u-blox NORA-W106 (ESP32-S3) Communication UART 2x I2C 1x, A4 (SDA), A5 (SCL) SPI D11 (COPI), D12 (CIPO), D13 (SCK). Use any GPIO for Chip Select (CS) Power I/O Voltage 3.3 V Input voltage (nominal) 6-21 V Source Current per I/O Pin 40 mA Sink Current per I/O Pin 28 mA Clock speed Processor up to 240 MHz Memory ROM 384 kB SRAM 512 kB External Flash 128 Mbit (16 MB) Dimensions Width 18 mm Length 45 mm

Arduino Giga R1 Rohs Compliant: Yes |Arduino ABX00067

Arduino GIGA Display Shield Introducing the GIGA Display Shield – your go-to touch screen solution for effortlessly integrating graphic interfaces into your projects. Designed to seamlessly harness the power of the new pin header connector positioned in the heart of GIGA R1 WiFi, this shield takes your projects to the next level with enhanced functionality. Unlock a world of possibilities with the GIGA Display Shield, which boasts a range of features, including a digital microphone, a 6-axis IMU, and an Arducam connector. These additional capabilities empower you to fully harness the potential of the 54 available pins, making it exceptionally convenient to craft handheld devices or dashboards to manage and oversee your project. Experience the ease of crafting intuitive interfaces with the GIGA Display Shield's user-friendly design and comprehensive feature set. Elevate your project's functionality and enhance the user experience with this state-of-the-art solution. Tech Specs Board Name Arduino GIGA Display Shield SKU ASX00039 Connectors Camera SOCKET 2ROW 20POS VERTICAL PASS THROUGH (Arducam compatible) Display Video F32Q-1A7H1-11020 Display Touch F32Q-1A7H1-11008 Display KD040WVFID026-01-C025A Size 3.97” Resolution 480x800 RGB Color 16.7M Touch Mode Five points and Gestures Interface I2C Sensors IMU BMI270 Microphone MP34DT06JTR

Arduino Opta Lite Board, Cortex M4/M7 Rohs Compliant: Yes |Arduino AFX00003

DEVELOPMENT BOARD, 32BIT, ARM CORTEX-M4F;

WISGATE EDGE LITE2 - EU

WISGATE EDGE LITE2 - USA

Arduino AKX00060 - Prototyping Kit Key features: Secure OTA Updates & Fleet management Easily accessible resources for the Portenta X* Modular container architecture Easily add LoRa® and Cat.M1 connectivity layer thanks to the Portenta Max Carrier Kit contains: Arduino Portenta X8 Arduino Portenta Max Carrier USB Hub LoRa antenna Cat.M1 antenna Power supply for Portenta Max Carrier Software included: Arduino Cloud for business 3 months voucher Machine learning tools for IoT Cloud Applications: Industrial automation Motion control HMI Industrial IoT gateway Smart Cities - building automation Smart kiosk Access monitoring

ARDUINO FUNDAMENTALS BUNDLE WITH ACTIVATION CODE ES