Display, 7" Touch Screen, Rpi Sbc; Screen & Display Type:7" Touchscreen Display; For Use With:Raspberry Pi Single Board Computers; Product Range:- Rohs Compliant: Yes |Raspberry-Pi RASPBERRYPI-DISPLAY..

Som, Rpi Compute Module 4 Sodimm, 2Gb Rohs Compliant: Yes |Raspberry-Pi CM4S02008

Som, Rpi Compute Module 4 Sodimm, 2Gb Rohs Compliant: Yes |Raspberry-Pi CM4S02032B

Som, Rpi Compute Module 4 Sodimm, 8Gb Rohs Compliant: Yes |Raspberry-Pi CM4S08016B

Antenna Kit, Raspberry Pi Compute Mod 4 Rohs Compliant: Yes |Raspberry-Pi SC0480(IP66)

Raspberry Pi Processor Broadcom System-On-Chip BCM2835

EnOcean Pi connects energy harvesting wireless devices with the Raspberry Pi to help control networks and automation systems at home or in the workplace.

Raspberry Pi Processor Broadcom System-On-Chip BCM2835

Compute Modules (CM) and Compute Module IO Boards (CMIO): In each kit you get a Compute Module, an IO Board, adaptors to convert the CMIO board camera and display interfaces to use the official Raspberry Pi Camera (and display when available later this year), 5V power supply and a micro USB cable for flashing the eMMC from a host PC.

Pi-Top Expansion Plate The pi-top Expansion Plate is a versatile interface for any project. It delivers a range of voltages (up to 12 volts) and includes everything you need to drive the motors and servos in this kit. Includes an IMU with accelerometer, gyroscope and magnetometer.

The 7 Touchscreen Monitor for Raspberry Pi gives users the ability to create all-in-one, integrated projects such as tablets, infotainment systems and embedded projects. The 800 x 480 display connects via an adapter board which handles power and signal conversion

Mechanical Drawing

CPU: Broadcom BCM2835, which can run at up to 1GHz.RAM: 512MBPower: 5V, supplied via micro USB connector, drawing 160mA (even when connected to an HD display).Dimensions: 65mm x 30mm x 5mmVideo & Audio: 1080P HD video output. Audio output via mini-HDMI connector.Storage: MicroSD card.Operating System: Linux, installed via NOOBS.

Introducing the Raspberry Pi Zero: Created by lady ada

Rainbow LED: 18 color, clip on card three lights of red, orange, yellow, green, blue and white

The Compute Module IO Board is a simple, open-source breakout board that you can plug a Compute Module into. It provides the necessary power to the module, and gives you the ability to program the modules Flash memory, access the processor interfaces in a slightly more friendly fashion (pin headers and flexi connectors, much like the Pi) and provides the necessary HDMI and USB connectors so that you have an entire system that can boot Raspbian (or the OS of your choice).

Raspberry Pi Camera Board: Omnivision OV5647 Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI Technology

The New Model A+ replaced the Model A in November 2014. The design is based around a Broadcom BCM2835 SoC, which includes an ARM1176JZF-S 700 MHz processor, VideoCore IV GPU, and 256 Megabytes of RAM. This revision A+ board features four mounting holes for easy installation, a built-in reset circuit, and can be powered via the USB data ports. The design does not include a built-in hard disk or solid-state drive, instead relying on an microSD card for booting and long-term storage. This board is intended to run Linux kernel based operating systems.

The Model B+ is the higher-spec variant of the Raspberry Pi. It replaced the original Model B in July 2014. Compared to the Model B it has: More GPIO. The GPIO header has grown to 40 pins, while retaining the same pinout for the first 26 pins as the Model B. More USB. We now have 4 USB 2.0 ports, compared to 2 on the Model B, and better hotplug and overcurrent behaviour. Micro SD. The old friction-fit SD card socket has been replaced with a much nicer push-push micro SD version. Lower power consumption. By replacing linear regulators with switching ones weve reduced power consumption by between 0.5W and 1W. Better audio. The audio circuit incorporates a dedicated low-noise power supply. Neater form factor. Weve aligned the USB connectors with the board edge, moved composite video onto the 3.5mm jack, and added four squarely-placed mounting holes.

The compute module contains the guts of a Raspberry Pi (the BCM2835 processor and 512Mbyte of RAM) as well as a 4Gbyte eMMC Flash device (which is the equivalent of the SD card in the Pi). This is all integrated on to a small 67.6x30mm board which fits into a standard DDR2 SODIMM connector (the same type of connector as used for laptop memory)