Configuration of the bq78PL114 to a custom series and parallel cell arranged pack is accomplished outside parameter tabs in bqWizard™ or the .ppcsv parameter configuration file. It is easy to set by loading an appropriate .tmap file to the device. This application report describes loading the .tmap file some considerations for the parallel cell count configuration and how to simply edit the .tm

Analog designers are frequently required to convert high-voltage signals to levels acceptable to low-voltage data converters with differential inputs. This paper describes solutions for this common task using modern amplifiers and typical power supplies. Three examples of conditioning ±10V bipolar signals for low-voltage analog-to-digital converters (ADCs) are shown: a single-supply design

AN-402 LM2889 RF Modulator

Turbo decoder lies at the heart of all of the third-generation (3G) wireless standards. The turbo coprocessors (TCP2) are programmable peripherals used to decode turbo codes. It is integrated into Texas Instruments TMS320TCI648x Digital Signal Processor (DSP). This application report gives the channel density data for TCP2 under various conditions the CPU load for pre-processing TCP2 input data i

AN-637 Realizing Trigonometric Functions with the Multifunction Converter LH0094

This paper describes a complete solution for digital measurement of acceleration. An AMP accelerometer sensor is used for the conversion between mechanical acceleration and electrical analog. This electrical signal is then conditioned using Texas Instruments? TLV2772 op amp (on the Universal Op Amp EVM) digitized using the TLV1544 ADC EVM and processed with the TMS320C5X EVM. This provides the u

Host Interface Control of the TPS65982 USB Type-C and PD Controller from a PC TPS65982, TPS65982-HIUTILITY

By using the general-purpose I/O pins in conjunction with two timers and an external interrupt one can develop a very flexible full-duplex UART in software. This document discusses the implementation of an interrupt-driven full-duplex asynchronous serial interface 9600-baud UART with 8 data bits 1 stop bit and no parity using the on-chip resources of the TMS320C3x.

Frequency Dithering With the UCC28950 and TLV3201

The ADS8364 16-bit parallel output analog-to-digital converter has a number of features that allow for an easy interface to the TMS320F2812™ digital signal processor. This application note focuses on configuring sampling and converting analog data presented to the ADS8364 ADC. Portions of ports A E and F are used for general-purpose control while the parallel data bus accepts data fro

This project AXIR_B (Digital Tracker) corresponds to a PCB that performs the following main tasks.- Deviation calculus and coordinates transformations.- Tracking and smoothing the rectangular (X Y Z) coordinates.- Interfacing with the pedestal and the Radar Manager.The Digital Tracker operates different algorithms during the three modes of the AXIR. The three modes of the AXIR ra

This document provides an example application for the Power Management Bus (PMBus) protocol implementation using the MSP430 as a master PMBus device. The PMBus protocol is an open-standard power-manag

In today?s complex embedded computing and data-communication systems interrupts areused extensively to service peripheral devices. However because of the pin-numberlimitation on packages most microprocessors have only one or two interrupt lines.Consequently several devices usually are connected to the same interrupt line. Thedrawback to this configuration is that the overhead process

This application note describes how to configure the internal registers of a TMS470R1x (TMS470) device for setting up inter-integrated communication (I2C) with an industry standard 24LC00 I2C memory device. This application report assumes the reader is familiar with the I2C protocol and is meant to supplement the TMS470 Inter-Integrated (I2C) Reference Guide (literature number SPNU223) and the dev

This application report provides an insight into several of the most frequently used infrared protocols and especially their flexible implementation using the TI MSP430FR4xx series of low-power microcontrollers.The MSP430FR4xx microcontrollers are primarily targeted at remote control application that are equipped with infrared modulation function and an LCD display. The infrared modulation combi

This application report discusses the use of the Texas Instruments LMH6554 as an ADC driver.

FDC1004 FDC1004: Basics of Capacitive Sensing and Applications

-48-V Supply Selection Circuit For TPS2350 Simplifies Fault Detection in ATCA Systems