Code Composer Studio IDE v3 - White Paper
Texas InstrumentsDesigned for the Texas Instruments (TI) high performance TMS320C6000™ (C6000™) and digital signal processor (DSP) platforms the Code Composer Studio™ IDE is a development environment that tightly integrates the tools needed to create winning DSP applications. Version 3.0 (Tuning Edition) includes tuning tools for optimizing applications.
Key components of the Code Compose
Selecting the Right Texas Instruments Signal Switch
Texas InstrumentsTexas Instruments offers a wide variety of electronic switches (digital, analog, bilateral, bilateral analog) in a variety of families, including CBT, CBTLV, HC, LV, and LVC. Depending on the applicat
How to Achieve Power-Path Management Function for bq2408x (Rev. A)
Texas InstrumentsThis application report presents a simple external circuit for achieving a power-path management function while maintaining an overvoltage protection function and blocking reverse current for low-cost
Bq241x0/3/4/5/8/9, bq24170/1/2, bq24133, bq24610/6 and bq24630/40/50 Comparison
Texas InstrumentsThis application report provides a comparison among bq241x0/3/4/5/8/9, bq24170/1/2, bq24133, and bq246xx . The document presents the main differences and describes the main features of each part. It
TMS320VC5509A DSP Hardware Designer's Resource Guide
Texas InstrumentsThe DSP Hardware Designer?s Resource Guide is organized by development flow and functional areas to make your design effort as seamless as possible. Topics covered include getting started, board desig
Maximizing Start-Up Loads w/LM3352 Regulated Buck-Boost Switched Cap Converter (Rev. B)
Texas InstrumentsThis application report discusses maximizing start-up loads with the LM3352 regulated buck/boost switched capacitor converter.
Layout Guidelines for Wireless Power Receiver (Generation 3
Texas Instrumentsbq51221 Layout Guidelines for Wireless Power Receiver (Generation 3
Time Division Duplexing (TDD) Adjusted Carrier Feedthrough Evaluation
Texas InstrumentsTime Division Duplexing (TDD) is a communication technique allowing for two-way communication within the same frequency band by alternating the transmission times of a device. An important parameter for devices in these TDD-transmission systems is the transient response of the adjusted carrier feedthrough when the devices are rapidly turned on and turned off. When a device transitions to the activ
Fully Differential OP Amps Made Easy
Texas InstrumentsFully differential op amps may be unfamiliar to some designers. This application report gives designers the essential information to get a fully differential design up and running.
Create an Inverting Power Supply from a Step-Down Regulator (Rev. B)
Texas InstrumentsTPS54160, TPS54360, TPS54340, TPS54560, TPS54540 Create an Inverting Power Supply from a Step-Down Regulator
Design Considerations for DC-DC Converters in Fast-Input Slew Rate Applications
Texas InstrumentsThis application report describes the ways to optimize the design of DC-DC converters (TPS54040-Q1 TPS54060-Q1 TPS54140-Q1 TPS54160-Q1 TPS54240-Q1 TPS54260-Q1 TPS57040-Q1 TPS57060-Q1 TPS57140-Q1 and TPS57160-Q1) in applications with fast transition at the input voltage on the rising and falling edges. First the issues faced under such a scenario are analyzed. Then design considerations
Power-Up Behavior of Clocked Devices (Rev. A)
Texas InstrumentsSome logic devices, such as flip-flops and shift registers, require the use of a clock input, typically designated CLK or CP. The state of the outputs of these devices change once an appropriate clock edge has occurred. Device datasheets specify whether the action occurs on a positive or negative edge of the clock. However, the behavior of a device upon power-up is not always specified before a valid clock edge has occurred.
Adding Hysteresis to Supply Voltage Supervisor
Texas InstrumentsSome applications require supply voltage hysteresis to keep a supply voltage supervisor (SVS) from falsely resetting the system due to voltage dips and glitches. This application report presents one solution for adding hysteresis to an SVS. The solution schematic is given along with component selection criteria and equations such that readers can appropriately scale the solution to their own re
How to Review a Multicell Switching Charger Schematic
Texas InstrumentsThis application report provides a checklist for reviewing a switching charger schematic and explains each item in the list.
Interfacing SD/MMC Cards With TMS320F28xxx DSCs
Texas InstrumentsThis application report and associated code implements the interfacing of Secure Digital (SD) or Multi-Media Card (MMC) types of Flash memory cards with the TMS320F28xxx digital signal controllers (DSCs). These cards can use serial peripheral interface (SPI) or parallel (SD) interface to connect to the host. This application report demonstrates the SPI mode and includes the schematics showing th
