The software demonstrates real-time D1 MPEG-2 encoding on the DM642 EVM. The demonstration encodes the captured frames and displays all the frames from the reconstruction loop of the encoder.

The demonstration uses:

• MPEG-2 encoder library optimized for DM642 EVM capable of real-time D1 encoding
• MPEG-2 encoder library implemented using XDAIS interfaces
• Sample integration of the MP

This application report describes the detailed methods of using the GPADC in the TPS65916, TPS65917-Q1, TPS659037, TPS659038-Q1, and TPS659039-Q1 devices.

The Low Power Mode 4.5 (LPM4.5) is used to achieve lowest power consumption in the MSP430F5xx devices. When the device enters LPM4.5 the internal regulator of the Power Management Module (PMM) is disabled thus switching off the supply voltage that is used to power the device core. The device core includes the JTAG and debug (EEM) logic of the device. To debug code while the device enters or exit

LMK04808, CDCE62005, DAC3482 Effects of Clock Noise on High Speed DAC Performance

The Burr-Brown REF102 is a buried-zener-based precision 10V reference. It has better stability and about five times lower output noise than band-gap-based voltage references such as the PMI REF-10. Still its output noise is about 600uVp-p at a noise bandwidth of 1MHz (the output noise of the PMI REF-10 is about 3000uVp-p at 1MHz).

This application report provides direction for programming the Control Words (also known as Control Mode Registers or CMR) of DDR3 Register Buffers which are compliant with the JEDEC SSTE32882 specification.

TLV320AIC31/32/33, TLV320AIC3101/04/05/06, TLV320AIC3204/3254 Configuring I2S to Generate BCLK from Codec Devices and WCLK from McBSP Port

Adjustable 3-Terminal Regulator for Low-Cost Battery Charging Systems

To achieve reliable power amplifier designs you must consider the stress on the amplifier compared to its power handling limitations. Power handling limits are specified by the Safe Operating Area (SOA) curves of the power amp. Stress on the amplifier depends on amplifier load and signal conditions which can be evaluated with straightforward techniques.

The industry is imposing increasingly aggressive testability requirements on modern electronics development. Existing designs require additional hardware modifications to provide all the testability functions. The JTAG/IEEE 1149.1 specification for 4-wire test bus interfaces or boundary-scan architecture provides a standard for built in testability functions. This document discusses the reliabilit

This document describes the design changes from the bq27541 (firmware version 1.12) to bq27541-v200 (firmware version 2.00). For ordering information and data sheet see the Texas Instruments Web site.

This document discusses special precautions that need to be taken when working with the TMS320C40 emulator. There are several potential problem situations:? The debugger will break any pending CPU/DMA access that is not completed within the time-out period. ? Comm port logic stops when the emulator is halting the device (in a breakpoint or between single steps). (However you can still wor

TVP5151 PCB Layout Guidelines

SB-113 Laser Beam Printer (LBP) Controller Solution Card

This application report gives an example of using the bq24650 charge management device to provide a high-efficiency switching-mode charging solution for the LiFePO4 battery.

This application report provides a component-by-component design guide for a boost converter-basedLED driver using the LM5022.

This application report presents an efficient and precise method on how to achieve the desired resonant frequency of configuring the trim array with only a few iterations and measuring the resonant frequency. First the minimum and maximum resonant frequency is measured; from this data a capacitance gradient is derived which allows a good prediction of the required capacitance. The calculated cap

The PCM9211 evaluation module (EVM) is designed to allow users to record and play back audio signals via a USB interface while running CodecControl software on a PC. The USB interface uses the TAS1020B USB interface device. This document presents a detailed description of the recording interface setup from an analog input to PC and discusses how to play back a digital signal from the PC via a USB

The Texas Instruments TFP101 is one device in a family of TI PanelBus™ flat panel display products that simplifies digital display systems design by offering value added flexibility and reliability to the system designer. The TFP101 is a DVI compliant flat panel digital receiver that supports display resolutions ranging from VGA to XGA in 24-bit true-color pixel format. The TFP101 offers de