Manufacturer

Displaying 5401 - 5420 of 6424

Application Notes from Texas Instruments

TAS5132DDV2EVM

Texas Instruments
The TAS5132EVM PurePath Digital™ customer evaluation module (EVM) demonstrates the integrated circuits TAS5086PAG and TAS5132DDV from Texas Instruments. This application report covers the EVM specifications audio performance and power efficiency measurements graphs and design documentation that includes schematics parts list layout and mechanical design.

DN-49 UC2577 Controls SEPIC Converter for Automotive Applications

Texas Instruments
The Single-Ended Primary Inductance Converter (SEPIC) can convert an input voltage to an output voltage that is higher, lower, or equal to the input. Conversion is performed without the use of expensi

Design Considerations for Avoiding Timing Errors during High-Speed ADC, LVDS Dat (Rev. A)

Texas Instruments
ADS6129, ADS6149 Design Considerations for Avoiding Timing Errors during High-Speed ADC, LVDS Dat

Coefficient RAM Access Mechanisms.. (Rev. D)

Texas Instruments
Coefficient RAM Access Mechanisms SC2117, TLV320AIC3111, TLV320AIC36, TLV320ADC3101, TLV320ADC3001, TLV320AIC3254, TLV320AI Coefficient RAM Access Mechanisms

bq40z50 Data Memory Programming for Mass Production

Texas Instruments
bq40z50 bq40z50 Data Memory Programming for Mass Production

Implementing DDR2 PCB Layout on the TMS320DM644x DMSoC (Rev. G)

Texas Instruments
This application report contains implementation instructions for the DDR2 interface contained on the TMS320DM644x digital signal processor (DSP) device. The approach to specifying interface timing for

Designing Non-Invert Buck-Boost (Zeta) Cnvrts w/a Buck P-FET Cntrl

Texas Instruments
Designing Non-Inverting Buck-Boost (Zeta) Converters with a Buck P-FET Controller

Implementation of Affine Warp Using TI DSP

Texas Instruments
Healthcare and medical research has seen increased usage of medical images in recent years. This usage often involves visualization of three-dimensional (3D) data sets as well as accurately relating information in different images for diagnosis treatment and basic science. Image registration and volume rendering operations often involve some combination of rotation scaling shifting and shearing

AN-286 Applications of the LM392 Comparator Op Amp IC (Rev. B)

Texas Instruments
This application note discusses the uses of the LM339 quad comparator and the LM324 op amp areamong the most widely used linear ICs today. The combination of low cost single or dual supply operationand ease of use has contributed to the wide range of applications for these devices.

Multichannel Assembly Code Processing on C5000(TM) DSP Family Devices

Texas Instruments
This document describes the multichannel processing methodology used in multichannel algorithm implementations available for wireless applications where the optimization level is very high. This efficient and reliable processing methodology can also be used in any domain where it is necessary to run several instances of the same algorithm. With little overhead this processing methodology adds val

IEC61000-4-2, IEC 61000-4-4 and IEC 61000-4-5 tests for TI?s protection devices

Texas Instruments
IEC61000-4-2, IEC 61000-4-4 and IEC 61000-4-5 tests for TI?s protection devices IEC61000-4-2, IEC 61000-4-4 and IEC 61000-4-5 tests for TI?s protection devices

3.3-V to 12-V High Efficiency Ceramic Only Non-Synchronous Boost Converter

Texas Instruments
This reference design describes the functionality of the controller in more detail. This design explains the procedures of a non-synchronous boost converter from 3.3 V to 12.0 V with TPS43000 PWM cont

Powering the TMS320VC5402 DSP Using the TPS60100, TPS76918, and the TPS3305-18

Texas Instruments
This report analyzes a low-cost, low-power supply design utilizing the TPS60100 dc-to-dc converter, the TPS76918 series regulator, and the TPS3305-18 power-supply supervisor to power DSP applications.

General Purpose Power Supply

Texas Instruments
General Purpose Power Supply

Calculating Gain for Audio Amplifiers (Rev. A)

Texas Instruments
This application report explains the different types of audio power amplifier configurations such as the single-ended (SE) the bridge-tied load (BTL) and the fully differential audio amplifier. Each configuration is illustrated with a block diagram gain equations and an example using realistic scenarios to illustrate to engineers how to calculate the gain of their audio amplifier.

TUSB8040A Design Guide

Texas Instruments
TUSB8040A TUSB8040A Design Guide

Bergeron Method: Graphically Determine Line Reflections In Transient Phenomena

Texas Instruments
The users of fast modern logic systems must closely consider the effect of line reflections on the system. This document describes the Bergeron method of determining line reflections in a system. Typical examples of its use and the results it produces are provided. The appendix contains Bergeron diagrams for no line termination and line termination by resistor by series resistor and resistor n

Power-Supply Solutions for Multivolt Altera FLEX 10KE and APEX 20K/KE FPGAs

Texas Instruments
This report is a reference for design engineers inexperienced with multivoltage devices but who are using Altera 2.5-V and 1.8-V multivoltage APEX 20K/20KE and FLEX 10KE field-programmable gate array (FPGA) products.

Displaying 5401 - 5420 of 6424

Latest Parts

SC1112

Raspberry Pi

$79.61 - $80.00

IN STOCK 12700
Buy

ASX00049

Arduino

* $38.94 - * $44.91

IN STOCK 3123
Buy

AD96685BRZ

Analog Devices Inc.

$1.72 - * $11.92

IN STOCK 4899
Buy

Reference Designs

RD006

Wurth Elektronik

RD006 - 3 W Dual-output isolated auxiliary supply for communication interfaces and measurement systems

CN0583

Analog Devices Inc.

Multistandard Micropower Verified Smoke Detection System-on-Module

Technical Resources

EVALUATION KITS

EVAL-AD7124-8SDZ

Analog Devices Inc.

$71.95 - * $76.84

IN STOCK 805
Buy
View All