This application report describes how to achieve a reliable and ultra low-power electronic water meter design using the MSP430F41x microcontroller from Texas Instruments. The innovative flow sensor I

AN095 -- Continuous Data Streaming Applications -Using Serial Synchronous Mode in CC110x a

The purpose of this application report is to provide help for configuring the PBIST module of TMS570LS series microcontrollers. It also explains the configurations the different algorithm test durations and the influence on current consumptions.

Live-insertion capability is an essential part of today?s high-speed data systems because those systems are expected to run continuously without being powered down. This application report delves into the cause and prevention of live-insertion and nanosecond-discontinuity effects using both simulation and actual test measurements from a specially built GTLP EVM. Hypothetical cases for precharge c

The serial peripheral interface (SPI) and the multichannel buffered serial port (McBSP)provide serial communication between devices such as microcontrollers DSPs DACs andADCs. Typically these serial interfaces are single-ended and are in close proximity. Differential line circuits increase the allowable distance between devices while maintaining data integrity. This report describes RS-485

The Texas Instruments Impedance Track™ (IT) fuel gauge is designed for reporting remaining battery capacity and run time accurately. To effectively accomplish this reporting a real application environment must be used for test results. The test board should be designed as similar to the real application circuit as possible. This application report outlines the procedure for implementing an accurac

DN603 -- CC-Antenna-DK Board #6 OTA Test Results (868 MHz & 2.4 GHz) with EB

GTL and BTL transceivers provide high-performance excellent signal integrity and cost-effectiveness in high-speed backplane and point-to-point applications. This document discusses the GTL and BTL devices input/output (I/O) structure power consumption simultaneous switching slew rate and signal integrity. Design considerations for using these devices are provided.

TLK3131, TLK3132, TLK3134, CDCM7005 TLK313x/CDCM7005 Multi-hop Performance

DN615 -- Design Notes

This application report provides the necessary information in order to use the voltage sensor of the CC112x and CC120x family. The voltage sensor can be used to monitor the supply and battery voltage (V_DD).

The TMS320F2837x and TMS320F2807x microcontrollers provide facilities for interfacing to external SDRAM memory through two external memory interface modules. The address space for this memory lies bey

This document discusses how to design an operational amplifier (op amp) with both gain and dc offset. The design requires no theory and very little math just working designs.

The TPS54120 is an integrated switcher and low-dropout (LDO) regulator optimized for high efficiencies and a low-noise output. This application report describes how to use the Enable Power Good and Slow Start pins in tracking and sequencing applications. Three different tracking and sequencing methods are described in this report: sequential ratiometric and simultaneous. Each of these methods

CC2541, CC2540, CC2590 AN120 -- Using CC2590 Front End with CC2541

This application report applies to current designs using the Texas Instruments ADS7813 device in a surface-mount SO-16 (DW) package. This document guidesusers of the ADS78xx device with regards to potential compatibility issues that can be encountered when upgrading to the new ADS85xx part series.

Extending the Signal Path Over Data Transmission Lines Using LVDS Signal Conditioning

This application note describes how a 120 MHz sample rate multi-channel digital down-conversion system can beimplemented using GRAYCHIP GC2011 Digital Filter and GC4014 Quad Digital Receiver chips.

The CC1190 is a range extender for 850-950 MHz RF transceivers transmitters and wireless microcontrollers (MCUs). It increases the link budget by providing a power amplifier (PA) for increased output power and a low-noise amplifier (LNA) with low noise figure for improved receiver sensitivity in addition to switches and RF matching for simple design of high performance wireless systems.

bq27510-G3 bq27510-G2 to bq27510-G3 Change List