Evaluation of Nickel/Palladium-Finished ICs With Lead-Free Solder Alloys
Texas InstrumentsA nickel/palladium (Ni/Pd) lead finish for integrated circuits (IC) was introduced in 1989. In 1998 solderability test results were published on Ni/Pd-finished components using a Sn/Ag/Cu/Sb…
200-W Interleaved Forward Converter Design Review Using TI's UCC28221 PWM Contro
Texas Instruments200-W Interleaved Forward Converter Design Review Using TI's UCC28221 PWM Controller
AN-1718 Differential Amplifier Applications Up to 400 MHz (Rev. B)
Texas InstrumentsThe LMH6515 is a fully differential amplifier optimized for signal path applications up to 400 MHz and hasa 200Ω input.
Using PWM Output as a Digital-to-Analog Converter on a TMS320F280x (Rev. A)
Texas InstrumentsThis application report presents a method for utilizing the on-chip pulse width modulated (PWM) signal generators on the TMS320F280x™ family of digital signal controllers as a digital-to-analog…
Power supply reference design for Samsung? s3c2416 using TPS650250 (Rev. A)
Texas InstrumentsTPS650250 Power supply reference design for Samsung? s3c2416 using TPS650250
How to Configure and Use the bq27410
Texas InstrumentsTI’s Impedance Track (IT)™ fuel gauge is designed for accurately reporting battery remaining capacity and run time. It is `necessary to configure and use the gauge correctly to achieve this.…
Sequential Addressing of I/O Ports on the TMS320C54x
Texas InstrumentsOn the Texas Instruments (TI) (tm) TMS320C54x the I/O port addresses are hard-coded in the opcodes for the PORTW (I/O port write) and PORTR (I/O port read) instructions. This document discusses…
External Slope Compensation for UCC2897A in Some Special Applications
Texas InstrumentsUCC2897A External Slope Compensation for UCC2897A in Some Special Applications
Current Sharing in Redundant Systems
Texas InstrumentsTPS2412, UCC39002 Current Sharing in Redundant Systems
Programming the TMS320VC5503/C5506/C5507/C5509/C5509A I2C Peripheral (Rev. A)
Texas InstrumentsThis application report demonstrates the procedure used to program the TMS320VC5503/C5506/C5507/C5509/C5509A inter-integrated circuit (I2C) peripheral module. Basic operations of the I2C…
Understanding the Differences Between CDC2509x/10x Devices
Texas InstrumentsThis application note provides information concerning the various revisions of the TI CDC2509/10 family of devices. In addition, it will assist designers with new and existing designs. Phase…
Design Considerations for Logic Products Application Book, Volume 3, December 20
Texas InstrumentsDesign Considerations for Logic Products Application Book, Volume 3, December 2000
PT78/79 Series ISR Thermal Considerations (Rev. A)
Texas InstrumentsPT78/79 Series ISR Thermal Considerations PT78 and PT79 ISR Series
Current Sensing With Near-Zero Common Mode Voltage with INA19xA-Q1
Texas InstrumentsThis report provides a summary of using the INA19xA-Q1 device when the common mode voltage is close to zero volts. In this low common-mode voltage region, the output voltage has a large error.…
Software Migration From TMS320DM642 to TMS320DM648/DM6437
Texas InstrumentsSoftware Migration From TMS320DM642 to TMS320DM648/DM6437 Application Report
XDS Target Connection Guide
Texas InstrumentsThis article has been contributed to the TI Embedded Processors Wiki. To see the most recently updated version or to contribute visit this topic…
Implementing Color Reproduction for TC236 CCD Sensor Using the TMS320C2xx DSP
Texas InstrumentsThe Charge-Coupled Device (CCD) sensor is widely used in many video applications such as scanners digital cameras video camcorders etc. In these video systems a processor or hardware circuit…
Low-Power Support Using Texas Instruments SN74SSTV16857 and SN74SSTV16859
Texas InstrumentsThe Texas Instruments SN74SSTV16857 and SN74SSTV16859 registers support the low-power mode of the DDR-DIMM. This application report explains the low-power mode and the features of the registers…
Setting Up and Simulating Interrupts on the TMS320C5x
Texas InstrumentsThis document contains an example that shows the code required to set up serial port interrupts on a 'C5x DSP. This technique can be applied to any other interrupt. Several code examples are…
